manualshive.com logo in svg

Emerson Tescom ER5000 Series, User Manual, Page: 132 / 248

Share
Download
Emerson Tescom ER5000 Series User Manual Download Page 132

 

ER5000

 — 

132

The ERTune™ Program: Basic Features

Resizing the Range Displayed by the Plot Screen Using 

the Mouse

IMPORTANT!

IMPORTANT!

Changes made to the Plot Screen display using the mouse 

or the Plot Screen menu commands only change the display of the Plot 
Screen. The ERTune™ program continues to track the full range of values for 
setpoint and feedback, even if the Plot Screen does not display them.

To change the actual range of feedback values tracked by the ERTune™ 
program, refer to the task 

To change the range of feedback values tracked 

by the ERTune™ program.

To toggle the display range of the vertical axis

1.  Double-click anywhere within the Plot Screen. This toggles 

the display between a 0% to 100% display and a -20% to 
120% display. 

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

If your application makes full use of the display range, the 

-20% to 120% display makes it easier to visually track setpoints and 
responses near the 0% and 100% levels.

To zoom the vertical axis display

1.  Click once within the Plot Screen at the level you want to set as 

the new maximum value, then a second time at the level you 
want to set as the new minimum value.

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

You may repeat this process to progressively increase the 

zoom level.

To return the vertical axis display to the default setting

1.  Double-click anywhere within the Plot Screen. 

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

You will return to the default display even if you have 

zoomed multiple times.

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Reviews:

No comments