Emerson Tescom ER5000 Series User Manual Download Page 239

Page: 239 / 248

ER5000

—

239

Certifications and Warranty

Conforms to all known European Union
requirements.
EMC DIRECTIVE 2014/30/EU
IEC/EN 61000-6-2: 2005
IEC/EN 61000-6-4: 2007/A1:2011

Is not certified but conforms to FM
Standards. FM Class 3600-1998 & FM Class
3615-2006

SPECIAL CONDITIONS FOR SAFE USE:

•

Make sure everything is properly
assembled before powering.

•

Do not open when an explosive
atmosphere is present.

•

Installation to be in accordance with the
latest edition of National Electrical Code.

•

The cable and conduit entry devices
shall be certified flame proof types,
suitable for the conditions of use and
correctly installed.

•

Unused conduit entry must be closed
with suitable blanking element.

•

Seal conduit entry within 18 inches.

•

Rated for 20.5 to 28.5 VDC,
340 mAmps.

•

Max working pressure: 110 PSIG

•

-20°C ≤ T

amb

≤ 60°C

•

Thread entry sizes are 1/8" - 27 NPT
and 1/2" - 14 NPT. Reference page 18
for locations.

•

The user/installer shall not remove any
of the three, 1/8”-27 NPT plugs that
are fitted into the base of the enclosure
as this will invalidate the Hazardous
Location Certification. Reference
page 18 for locations.

Hazardous Locations Special Requirements and Certification for the ER5050

Copies of all certification documents are available at www.tescom.com. Click on the

CERTIFICATIONS

Quick Link.

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Search results

Summary of Contents for Tescom ER5000 Series

Reviews:

Emerson Tescom ER5000 Series, User Manual, Page: 239 / 248

Search results

Summary of Contents for Tescom ER5000 Series

Reviews: