manualshive.com logo in svg

Emerson Tescom ER5000 Series, User Manual, Page: 117 / 248

Share
Download
Emerson Tescom ER5000 Series User Manual Download Page 117

ER5000

 — 

117

The ERTune™ Program: Basic Features

Where to Find the ERTune™ Program Files on Your PC

The ERTune™ program creates two folders on your C: drive 
during installation.

On PCs running Windows 7, the program files, including the 
program executables, device drivers, support files and reference 
materials, are located at:

 

C: -> Program Files (x86) -> Emerson -> ERTune

.

On PCs running previous versions of Windows, this is located at:

C: -> Program Files -> Emerson -> ERTune

.

A separate folder is created for data files generated by the 
program. On PCs running Windows 7, this is located at:

C: -> Program Data -> Emerson -> ERTune

.

On PCs running previous versions of Windows, this is located at:

C: -> Documents and Settings  -> All Users -> Application Data -> Emerson -> ERTune

.

This folder is the default location for configuration files, Profiles 
and data acquisition files. The Windows Navigator window will 
default to this folder. You may save the data files generated by 
your application in another location, if you prefer.

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Reviews:

No comments