manualshive.com logo in svg

Emerson Tescom ER5000 Series, User Manual, Page: 131 / 248

Share
Download
Emerson Tescom ER5000 Series User Manual Download Page 131

 

ER5000

 — 

131

The ERTune™ Program: Basic Features

Figure 48: The Active Plot Screen Display

Figure 48 shows all the 
elements of the active Plot 
Screen display as the ER5000 
responds to step changes in 
setpoint (red line).
The response is tracked through 
the feedback (blue line). 
The main (left) vertical axis 
and the horizontal axis have 
been customized using the 
commands in 

The Plot Screen 

Menus — The Main Axis Menu

. 

In this application, the 
ER5000’s internal sensor is 
also being tracked directly 
as an 

Added Variable

 (green 

line), which has been added to 
the Plot Screen using 

The Plot 

Screen Variable Controls

. 

The Secondary Axis

 displays 

the range for the internal 
sensor. The green line tracks 
to this range.

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Reviews:

No comments