Emerson Tescom ER5000 Series User Manual Download Page 133

Page: 133 / 248

ER5000

—

133

The ERTune™ Program: Basic Features

To zoom the display of both the vertical and horizontal axes

1. Drag a rectangular marquee within the active area of the

Plot Screen.

NOTE

CAUTION

WARNING

The marquee selection must begin and end within the

active area of the Plot Screen.

2. The Plot Screen zooms to display the marqueed area.

NOTE

CAUTION

WARNING

You may repeat this process to progressively increase the

zoom level.

Figure 49: Marquee select in the Plot Screen

To return both axes to the default display settings

1. Double-click anywhere within the Plot Screen.

NOTE

CAUTION

WARNING

If you have zoomed multiple times using a marquee, each

double-click will zoom out one level. Continue to double-click until
you reach the default settings.

NOTE

CAUTION

WARNING

You can also zoom both axes in and out using the scroll

wheel on a three-button mouse.

IMPORTANT!

The Plot Screen should be stopped before

resizing using a marquee selection.

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Search results

Summary of Contents for Tescom ER5000 Series

Reviews:

Emerson Tescom ER5000 Series, User Manual, Page: 133 / 248

Search results

Summary of Contents for Tescom ER5000 Series

Reviews: