manualshive.com logo in svg

Emerson Tescom ER5000 Series, User Manual, Page: 242 / 248

Share
Download
Emerson Tescom ER5000 Series User Manual Download Page 242

ER5000

 — 

242

Setting up the ERTune™ Program on Windows 8 PCs

Installing the .NET Framework 3.5

If you are running Windows 8 on your PC, the first time you open 
the ERTune™ program you may see this message:

 

The ERTune™ application was designed using the .NET Framework 3.5, 
to allow for compatibility with previous Windows operating 
systems. Windows 8 is built on the .NET Framework 4.5 and 
does not include .NET Framework 3.5 by default. However, the 
.NET Framework 3.5 can easily be downloaded and installed.

Note that you will need to be connected to the Internet before 
you begin. The procedure is as follows:

1.  Click 

Download and install this feature

 in the message window. 

Windows will oversee the download and installation.

2.  Once the .NET Framework 3.5 has been installed, you will need 

to verify the feature is turned on.

3.  Open the Charms bar by moving the mouse cursor into the 

upper right or lower right corner of the screen.

4.  Select Search.

   

(continued next page)

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Reviews:

No comments