Emerson Tescom ER5000 Series User Manual Download Page 136

Page: 136 / 248

ER5000

—

136

The ERTune™ Program: Basic Features

To change the horizontal axis using the Main Axis Menu

1. Select

Main Axis -> Time

. The Enter Time window opens.

2. Enter the number of seconds for one cycle of the Plot Screen.
3. Click

. The Plot Screen rescales to the new cycle time.

NOTE

CAUTION

WARNING

If you change the cycle time of the horizontal axis, you

must use the

Time

command again if you wish to reset the axis to

its original cycle time.

To change the main (left) vertical axis using the Main Axis Menu

1. Select

Main Axis -> Minimum Vertical

to change the minimum

value for the main axis display.
Select

Main Axis -> Maximum Vertical

to change the maximum

value for the main axis display.

2. Enter a new value.
3. Click

. The display rescales using the new value.

NOTE

CAUTION

WARNING

Repeat these steps for both menu items if you wish to set

new values for both the minimum and maximum of the display.

To reset the main (left) vertical axis to its original values using the
Main Axis Menu

1. Select

Main Axis -> Rescale Vertical

2. The main vertical axis of the Plot Screen returns to its original

display range.

IMPORTANT!

If you double-click in the Plot Screen after

changing the vertical axis using the menu commands, the display
will revert to its toggle between the original 0% to 100% range
and -20% to 120% range and you will lose the values you set using
the commands.

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Search results

Summary of Contents for Tescom ER5000 Series

Reviews:

Emerson Tescom ER5000 Series, User Manual, Page: 136 / 248

Search results

Summary of Contents for Tescom ER5000 Series

Reviews: