manualshive.com logo in svg

Emerson Tescom ER5000 Series, User Manual, Page: 107 / 248

Share
Download
Emerson Tescom ER5000 Series User Manual Download Page 107

ER5000

 — 

107

Installation Variations

Wiring Variations for Additional Functions

Digital Outputs 

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

This feature is only available on “F” models of the ER5000.

The ER5000 can provide digital outputs to the rest of the system. 
Refer to Table 25 for correct wiring.

Table 25: Wiring for Digital Outputs 

J3 Pins

Wire Color

Function

1

brown

+setpoint input

2

red

-setpoint input

3

orange

+feedback input

4

yellow

-feedback input

5

green

-RS485 network connection

6

blue

+RS485 network connection

7

violet

+24V DC power

8

gray

24V return (power ground)

9

white

+5V output (5 mA max.)

10

black

analog signal/board ground

*

11

*

pink

analog signal output

(active in Enhanced “F” models ONLY)

12

tan

analog signal/board ground

J4 Pins

Wire Color

Function

1

brown/white

+aux input #1

2

red/black

-aux input #1

3

orange/black

+aux input #2

4

yellow/black

-aux input #2

5

green/white

suspend control

6

black/white

digital output/board ground

7

blue/white

digital output #1

8

gray/black

digital output #2

(continued next page)

 WARNING

The controller must be disconnected from the power supply before 
any additional wiring or change to jumper configuration is 
performed. Do not reconnect the power supply until all additional 
wiring connections have been made and are properly installed.

BLACK/WHITE

LOAD 2

LOAD 1

GRAY/BLACK

BLUE/WHITE

POWER SUPPLY

12V DC

120V AC

SOLID STATE 

RELAY

MECHANICAL 

RELAY

VIOLET

Figure 42: ER5000 Digital Outputs 

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Reviews:

No comments