manualshive.com logo in svg

Emerson Tescom ER5000 Series, User Manual, Page: 110 / 248

Share
Download
Emerson Tescom ER5000 Series User Manual Download Page 110

 

ER5000

 — 

110

Installation Variations

Installing a Hazardous Location  
Model (ER5050)

 WARNING

Install conduit rated for your Hazardous Location 

using local and national electrical codes which 

apply to the application.
Conduit must be sealed within 18" of conduit’s 

point of entry into the ER5050.
Make sure everything is properly assembled 

before powering. 
DO NOT open cover when an explosive 
atmosphere is present. 
The cable and conduit entry devices shall be 

certified flame proof types, suitable for the 

conditions of use and correctly installed.
Unused conduit entry must be closed with 

suitable blanking element.

Click this link

 to view all Hazardous Location 

certifications and specifications.

 

ER5050 
Supply Pressure 
110 psig / 7.5 bar

Adaptor

External Transducer 
Rated For Use In 
Hazardous Location

Junction Box Rated 
For Use In Hazardous 
Location

Hazardous 
Location 
Conduit Cables 
and Hubs

Typical Conduit Hub:

Installation using a hole 
“through the enclosure” with 
a grounding locknut instead 
of a metal backplate.

Conduit

O-Ring

Set Screw

Ground Wire

“Increased Safety” 

Grounding Locknut

Hazardous 

Location Hub 

or Cable Gland

PC Located 
In Room Separate 
From Hazardous Area 

RS485 
Connection

Inlet Pressure

Outlet Pressure To Process 

Regulator

Figure 44: Typical Hazardous Location ER5050 Application

Controller, with adaptor, is mounted to an air actuated regulator. 
Feedback is from the external transducer. All wiring run through 
junction box that meets Hazardous Location specification.  
Setpoint is from a Profile downloaded from the PC.

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Reviews:

No comments