ELTRA CS-2000 Service Manual Download Page 8 | Manualshive

Page: 8 / 160

background image

Discharging the oscillator

8

NOTICE

Nature of the property damage

Source of property damage
–

Possible consequences if the instructions are not observed.

•

Instructions on how the dangers are to be avoided.

We also use the following signal word in the text or in the instructions on action to be taken:

NOTICE

2

Discharging the oscillator

Pos : 3 / 0015 ELTR A/ 0099 Ger ät eneutral/ St andard Modul e Eltra/9918 St andard Modul Entl aden des Oscill at ors CS800/2000 @ 11\ mod_1440744686940_9.doc x @ 87278 @ @ 1

In order to carry out work on the oscillator of the CS800/2000, it is necessary to ensure that the
oscillator has no stored energy. This is achieved by short circuiting the various potentials.

Attention:

This activity may only be carried out by a qualified electrician with sound knowledge of the
CS800/2000 devices.

Only the Eltra discharge set (Order Number 11001-2005) may be used for discharging. The
discharge set must always be inspected for visible faults before use.

1000V insulating gloves (order number 8840-0453) must be worn during the discharging
process to prevent an electric shock.

The protective measure is only effective if the discharge set and the insulating gloves are
always worn together.

Discharge set: 11001-2005

Insulating gloves 1000V: 88400-0453

«
...
6
7
8
9
10
...
»

Summary of Contents for CS-2000

































































































































































Reviews:

No comments

Related manuals for CS-2000

Brand: OfiTE Pages: 24

Brand: 4iiii Pages: 3

Brand: LaserLine Pages: 24

Brand: Han Seung Pages: 2

Brand: Omega Pages: 74

Brand: Omega Pages: 24

Brand: Sensia Pages: 16

Brand: Vanguard Instruments Company Pages: 62

Brand: Vanguard Instruments Company Pages: 58

Brand: Omega Pages: 31

Brand: IFM Pages: 38

Brand: ICP DAS USA Pages: 71

Brand: CONDTROL Pages: 11

Brand: Milwaukee Pages: 17

Brand: AEMC Pages: 4

Brand: Orange Research Pages: 2

Brand: Sub Aqua Pages: 4

BioTector B3500C

Brand: Hach Pages: 165

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands