ELTRA CS-2000 Service Manual Download Page 108

Page: 108 / 160

Service

108

Tube to squeeze:

Leak location:

Exhaust valve (V9)

Flow meter (25)

CO2-Paths (26)

SO3-Trap (27) or oxidizing furnace
tube (28)

SO2-Path (29) or flow sensor (30)

Regulator valve (V6)

Bypass valve (V4), check for 24 V
DC on the coil

Purge valve (V3), check for 0 V DC
on the coil

Lance valve (V2), check for 24 V DC
on the coil

ATTENTION

do not cause a short circuit while measuring, otherwise the drivers will be

destroyed. See chapter

“

Electronic drivers malfunctioning

”.

–

If the voltages on V2, V3, or V4 are wrong, then replace the electronic drivers.

Pos : 7. 10 /0025 Übersc hrift en/ELTRA 1.1 Übersc hrift en/11 Sol enoi d val ves cleaning ELTR A @ 6\ mod_1369643206541_9.doc x @ 42465 @ 2 @ 1

5.5 Solenoid valves cleaning

Pos : 7. 11 /0010 ELTR A/ 0015 s ervic e_ins truc tions/C S-2000_s er vice/ 15 Ser vic e_C S-2000/1530 Modul Cleani ng s olenoi d val ves @ 9\ mod_1425543480470_9. doc x @ 74766 @ @ 1

Fig. 92: Solenoid valve 2/2

3 - 1 3 - 1

Summary of Contents for CS-2000

































































































































































Search results

Summary of Contents for CS-2000

Reviews:

Related manuals for CS-2000

Brands by name

Popular brands

ELTRA CS-2000, Service Manual

Search results

Summary of Contents for CS-2000

Reviews:

Related manuals for CS-2000

Brands by name

Popular brands