ELTRA CS-2000 Service Manual Download Page 158

Page: 158 / 160

Index

158

Leak check induction furnace ........................... 106

Leak checking ................................................... 104

Leakage in the furnace area ............................. 105

Leakage outside the furnace area .................... 106

Left hand side power wiring .............................. 139

Left hand side view ........................................... 120

Linearity correction ............................................. 93

Lo C .................................................................... 80

Lo S ..................................................................... 80

LoC preamp ........................................................ 80

Long C path ........................................................ 80

Long S path ........................................................ 80

Loud buzzing sound when the generator turns on

........................................................................ 26

Low carbon sample too long combustion of a very

........................................................................ 66

Lower sulphur range ........................................... 85

Maintenance ..................................................... 152

Measurements .................................................... 22

Measurements - high voltage transformer .......... 23

Measurements on TP9 ....................................... 20

Measuring the voltage ........................................ 29

microcontroller board TP13 ................................ 51

microcontroller board TP9 .................................. 51

Miscellaneous ................................................... 118

Moderate or mild injury ......................................... 7

Mortal injury .......................................................... 7

Negative drift after start ...................................... 59

New flow sensor ................................................. 75

No combustion .............................................. 18, 28

No combustion induction furnace operation ....... 18

No cumbustion resistance furnace operatio ....... 27

No flow ................................................................ 19

No or low oxygen pressure ................................. 45

No oxygen pressure ............................................ 18

Noise reasons ..................................................... 48

Noise too high ..................................................... 48

Notes on service instructions ................................ 7

Old flow sensor ................................................... 75

Ordering numbers ............................................. 118

Ordering Numbers resistance furnace .............. 134

Organic materials (Oil, Coal, foodstuffs) ........... 154

Oscillating circuit ............................................... 127

Oscillator ............................................................. 64

Oscillator blower cleaning ................................... 64

Outflow valve ..................................................... 47

Outflow valve does not close ............................. 47

Outlet tap not properly open .............................. 14

Outlet tap of the oxygen bottle is not properly

open................................................................ 16

Outputs (base lines about 8VDC. For golden

paths adjust 6VDC) ........................................ 79

Oxygen

no flow ............................................................ 38

Oxygen gauge .................................................... 53

Oxygen pressure falls when the furnace opens 49

Oxygen pressure goes up very slowly ............... 52

Oxygen purifying furnace ................................. 134

Oxygen regulator ......................................... 53, 90

Oxygen solenoid valve (V5) may be defective .. 46

Oxygen supply is interchanged with the

compressed air supply ................................... 16

Path window broken........................................... 67

Path window not sealed ..................................... 67

Pin 7 ................................................................... 20

Pneumatic parts ................................................. 87

Pneumatics ........................................................ 86

Pneumatics (photo) ............................................ 31

Pneumatics (schematically) ............................... 30

Pneumatics adjusting for correct furnace

movement ....................................................... 88

Pneumatics parts ............................................... 86

power supply fluctuates ..................................... 48

Power switch ...................................................... 50

PR1 .................................................................... 90

PR2 .................................................................... 92

Preamplifier ........................................................ 80

Pre-purging ........................................................ 19

Pressure gauge .................................................. 49

Pressure regulation ............................................ 90

Programm screenshot (graph example 1) ......... 66

Programm screenshot (graph example 2) ......... 67

Programm screenshot (graph example 3) ......... 68

Programm screenshot (graph example 4) ......... 69

property damage .................................................. 7

Pump voltage attenuator cotton wool dirty......... 57

Pump voltage blockage lower connection glas

tube................................................................. 56

Pump voltage furnace ........................................ 58

Pump voltage IR-cell is blocked ......................... 57

Pump voltage leakage ....................................... 57

Pump voltage too high ....................................... 54

Pump voltage too high faults ............................. 56

Summary of Contents for CS-2000

































































































































































Search results

Summary of Contents for CS-2000

Reviews:

Related manuals for CS-2000

Brands by name

Popular brands

ELTRA CS-2000, Service Manual

Search results

Summary of Contents for CS-2000

Reviews:

Related manuals for CS-2000

Brands by name

Popular brands