ELTRA CS-2000 Service Manual Download Page 21

Page: 21 / 160

Faults

frequent problem. Tighten the screws of the plug properly, to ensure a proper connection to the
board.

Checking the generator tube

DANGER

Mortal danger from electric shock

Exposed power contacts - High Voltage

Ensure that the power switch is at position 3.

Check if the filament of the generator tube glows:

This can be easily checked:

Through the air vent holes of the furnace, the reflected light of the glowing filaments (heater of
the cathode) should be visible.

Fig. 13: Air vent holes of the furnace

The

filament of the generator tube doesn’t glow

Check the voltage of the filament, on the transformer, there should be 10 V AC on the
secondary. If not, then measure 220 V AC on the primary, leads 2-3.

NOTICE

Set the power switch to pos. 1 before removing the tube, although it would be best to
completely turn off the device and unplug the power cord.

DANGER

Mortal danger from electric shock

Exposed power contacts - High Voltage

Before touching any components or wiring, make sure the capacitors are discharged

Summary of Contents for CS-2000

































































































































































Search results

Summary of Contents for CS-2000

Reviews:

Related manuals for CS-2000

Brands by name

Popular brands

ELTRA CS-2000, Service Manual

Search results

Summary of Contents for CS-2000

Reviews:

Related manuals for CS-2000

Brands by name

Popular brands