ELTRA CS-2000 Service Manual Download Page 18

Page: 18 / 160

Faults

Fig. 5: HF-42

Fig. 6: Jumper position for gas saving mode

Fig. 7: Jumper position for continuous flow

In this case there is continuous flow when the main power switch is on Position 2.

Resistance furnace operation:

The flow sensor (same sensor also used in induction operation)

The electronic board PC-

2 (see chapter “

Gas flow controller and jumper settings

”).

The gas pump (see chapter “

Gas flow system

”).

Pos : 3. 6 / 0025 Ü bersc hrift en/ELTR A 1. 1 Ü bersc hrift en/ 11 N o combustion @ 9\ mod_1425544797746_9.doc x @ 74944 @ 2 @ 1

3.3 No combustion

Pos : 3. 7 / 0010 ELTR A/ 0015 s er vice_i nstr uctions /CS- 2000_s er vic e/05F aul ts_C S-2000/0515 M odul No combustion @ 9\ mod_1425539352573_9.doc x @ 74117 @ 33333334444444 @ 1

3.3.1 Induction furnace operation

After clicking START of analysis or pressing F5 but the sample doesn’t burn, check the reports
in the “status window” on the pc screen.

The following describes how to proceed depending on the displayed message

No oxygen pressure

See Chapter

“No or low oxygen pressure”

Summary of Contents for CS-2000

































































































































































Search results

Summary of Contents for CS-2000

Reviews:

Related manuals for CS-2000

Brands by name

Popular brands

ELTRA CS-2000, Service Manual

Search results

Summary of Contents for CS-2000

Reviews:

Related manuals for CS-2000

Brands by name

Popular brands