manualshive.com logo in svg

ELTEX LTP-4X, Operation Manual

The ELTEX LTP-4X Operation Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines for seamless operation of your ELTEX LTP-4X device. Visit our website to access the manual and make the most of your product's capabilities.

Share
Download
background image

 

60 

ont_flapping 

ONT flapping 

- 

download 

File download completed successfully / with 
errors 

- 

battery_power 

Switch ONT to battery power 

- 

battery_low 

ONT battery low 

Set in ONT 

lan_los 

ONT Ethernet port lost connection 

- 

ont_config 

Configuration of the connected ONT 

valid/invalid 

- 

file_delete 

File deleted successfully / with errors 

- 

physical_layer_errors 

Physical layer errors on Ethernet ports 

- 

physical_layer_block 

Ethernet port blocked 

- 

link 

Ethernet port status changed (up/down) 

- 

logout 

User logged out 

- 

ont_dying_gasp 

Dying Gasp signal received from ONT 

- 

ont_rei 

Remote Error Indication (REI) 

- 

ont_power_off 

ONT power off 

- 

config_change 

OLT configuration changed 

- 

shutdown 

SNMP agent shut down 

- 

oms 

OMS-MIB operation completed successfully / 
with errors 

- 

ont_state_changed 

ONT status changed 

- 

ont_config_changed 

ONT configuration changed 

- 

gpon_port_state_changed 

OLT channel configuration changed 

- 

pon_alarm_gpon_port 

Event related to OLT channel 

- 

pon_alarm_onui 

Event related to ONT 

- 

ont_update_inprogress 

Updating ONT firmware 

- 

olt_device_reset 

Resetting OLT chip 

- 

ont_signal_degrade 

The signal received from OLT is below the 
threshold value 

–28 dBm 

ont_high_rx_power 

The signal received from ONT is above the 
threshold value 

–8 dBm 

ont_low_rx_power 

The signal received from ONT is below the 
threshold value 

 

gpon-port-ont-count-overflow 

ONT number on channel exceeded 

 

olt_device_not_working 

GPON OLT configuration was loaded 

successfully / with errors 

- 

Summary of Contents for LTP-4X








































































































































































































Reviews:

No comments

Related manuals for LTP-4X

XDS 910 Reference Manual preview
910
Brand: XDS Pages: 99
D-Link DIR-862L Manual preview
DIR-862L
Brand: D-Link Pages: 4
D-Link DIR-860L Quick Install Manual preview
DIR-860L
Brand: D-Link Pages: 2
D-Link DIR-850L Resetting Manual preview
DIR-850L
Brand: D-Link Pages: 9
D-Link DIR-850L Setup And Installation Manual preview
DIR-850L
Brand: D-Link Pages: 8
D-Link DIR-865L Specifications preview
DIR-865L
Brand: D-Link Pages: 3
D-Link DIR-867 Quick Install Manual preview
DIR-867
Brand: D-Link Pages: 28
D-Link DIR-X1530 Quick Start Manual preview
DIR-X1530
Brand: D-Link Pages: 2
D-Link DSL-2540B - ADSL2/2+ Modem With EN Router Quick Install Manual preview
DSL-2540B - ADSL2/2+ Modem With EN Router
Brand: D-Link Pages: 12
D-Link DIR-882 Quick Installation Manual preview
DIR-882
Brand: D-Link Pages: 62
Dahua DHI-NVR5224-24P-4KS2 Quick Start Manual preview
DHI-NVR5224-24P-4KS2
Brand: Dahua Pages: 24
Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Brand: Paradyne Pages: 2
Paradyne Hotwire 6381 Installation Instructions Manual preview
Hotwire 6381
Brand: Paradyne Pages: 20
Paradyne Hotwire 6381 Upgrade Instructions preview
Hotwire 6381
Brand: Paradyne Pages: 2
Zhone Hotwire 6381 Quick Installation Instructions preview
Hotwire 6381
Brand: Zhone Pages: 2
IBM 3101 Maintenance Information preview
3101
Brand: IBM Pages: 63
mikroElektronika CAN SPI click Quick Start Manual preview
CAN SPI click
Brand: mikroElektronika Pages: 3
Renesas F-ZTAT H8/3048 Series User Manual preview
F-ZTAT H8/3048 Series
Brand: Renesas Pages: 34

Brands by name

Popular brands

Load more brands