manualshive.com logo in svg

ELTEX LTP-4X, Operation Manual

The ELTEX LTP-4X Operation Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines for seamless operation of your ELTEX LTP-4X device. Visit our website to access the manual and make the most of your product's capabilities.

Share
Download
background image

 

130 

        Bridge group:                                  11 
        Spanning tree for bridge group:                false 
        Multicast enable:                              false 
        Multicast port settings: 
            Upstream igmp vid:                         1 
            Upstream igmp prio:                        0 
            Upstream igmp tag control:                 pass 
            Downstream multicast vid:                  98 
            Downstream multicast prio:                 0 
            Downstream multicast tag control:          remove-tag 
            Max groups:                                0 
            Max multicast bandwidth:                   0 
        Shaper downstream: 
            Enable:                                    false 
            Commited rate:                             1000000 
        Shaper upstream: 
            Enable:                                    false 
            Commited rate:                             1000000 

... 

Step 11. 

Set up a management profile. To do this, create a cross-connect profile and assign it with the 

management 

type and the 

bridged 

model: 

LTP-8X(config)# profile cross-connect management 
LTP-8X(config-cross-connect)("management")# bridge 
LTP-8X(config-cross-connect)("management")# outer vid 9 
LTP-8X(config-cross-connect)("management")# type management

  

Step 12. 

Check the changes made. 

 
LTP-8X(config-cross-connect)("management")# do show profile cross-connect management  
    Name:                                              'management' 
    Description:                                       'ONT Profile Cross Connect 3' 
    Model:                                             ont 
    Bridge group:                                      255 
    Tag mode:                                          single-tagged 
    Outer vid:                                         9 
    Outer cos:                                         unused 
    Inner vid:                                         - 
    U vid:                                             untagged 
    U cos:                                             unused 
    Mac table entry limit:                             unlimited 
    Type:                                              management 
    IP host index:                                     0 
    Priority queue:                                    0 

 

Summary of Contents for LTP-4X








































































































































































































Reviews:

No comments

Related manuals for LTP-4X

C&H Technologies EM405-8 Manual preview
EM405-8
Brand: C&H Technologies Pages: 46
Paradyne 3172 Quick Reference preview
3172
Brand: Paradyne Pages: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Brand: Paradyne Pages: 2
Pantech Sprint PX-500 Quick Start Manual preview
Sprint PX-500
Brand: Pantech Pages: 17
Profile LS901-E1 Instruction Manual preview
LS901-E1
Brand: Profile Pages: 6
National Instruments NI-9252 Calibration Procedure preview
NI-9252
Brand: National Instruments Pages: 9
NETGEAR WGR614 - Wireless-G Router Wireless Reference Manual preview
WGR614 - Wireless-G Router Wireless
Brand: NETGEAR Pages: 116
Lanner NCA-1040 User Manual preview
NCA-1040
Brand: Lanner Pages: 59
Abocom WR5502 User Manual preview
WR5502
Brand: Abocom Pages: 63
HighPoint SSD7540L Quick Installation Manual preview
SSD7540L
Brand: HighPoint Pages: 10
Areca ARC-12x4 Series Quick Installation Manual preview
ARC-12x4 Series
Brand: Areca Pages: 2
A.E.B. ARCHIMEDE Fitting Instructions And Warranty Workbook preview
ARCHIMEDE
Brand: A.E.B. Pages: 28
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Brand: IEI Technology Pages: 142
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Brand: RadioSPECTRAL Pages: 2
ZALMAN VF2000 LED User Manual preview
VF2000 LED
Brand: ZALMAN Pages: 9
MICRADIGITAL F5D7630uk4A-E Speci?Cations preview
F5D7630uk4A-E
Brand: MICRADIGITAL Pages: 2
Pilz PNOZ mc3p Operating Instructions Manual preview
PNOZ mc3p
Brand: Pilz Pages: 12
Freescale Semiconductor M68HC08 series Designer Reference Manual preview
M68HC08 series
Brand: Freescale Semiconductor Pages: 124

Brands by name

Popular brands

Load more brands