manualshive.com logo in svg

ELTEX LTP-4X, Operation Manual

The ELTEX LTP-4X Operation Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines for seamless operation of your ELTEX LTP-4X device. Visit our website to access the manual and make the most of your product's capabilities.

Share
Download
background image

 

64 

Step  2. 

Add  untagged  interfaces  by  using  the 

untagged

  command  if  needed.  Pass  interface  type  and 

number (or a range) as parameters. 

LTP-8X(switch)(config-vlan)# untagged front-port 1

 

Step 3. 

Delete all unnecessary interfaces from the VLAN with the help of the 

forbidden

 command. Pass 

interface type and number (or a range) as parameters.

 

LTP-8X(switch)(config-vlan)# forbidden 10G-front-port 0 – 1 
LTP-8X(switch)(config-vlan)# forbidden front-port 0 , front-port 2 , front-port 3

 

Step 4. 

Disable IGMP snooping by using the 

no ip igmp snooping enable

 command if needed.

 

LTP-8X(switch)(config-vlan)# no ip igmp snooping enable

 

Step 5. 

Configure the IGMP querier if needed. It can be enabled with the help of the 

ip igmp snooping 

querier enable

 command. 

The  fast-leave  mode  is  enabled  by  means  of  the 

ip  igmp  snooping  querier  fast-leave

  command.  By 

default, this mode is disabled.  

DSCP and 802.1P marking for IGMP query is configured by means of the 

ip igmp snooping querier user-

prio 

and 

ip igmp snooping querier dscp commands.

 

LTP-8X(switch)(config-vlan)# ip igmp snooping querier enable 
LTP-8X(switch)(config-vlan)# ip igmp snooping querier fast-leave 
LTP-8X(switch)(config-vlan)# ip igmp snooping querier user-prio 4 
LTP-8X(switch)(config-vlan)# ip igmp snooping querier dscp 40 

Step 6. 

Configure IGMP if needed. 

Compatible versions (v1, v2, v3, or their combination):

 

LTP-8X(switch)(config-vlan)# ip igmp version v2-v3

 

Interval between queries:

 

LTP-8X(switch)(config-vlan)# ip igmp query-interval 125

 

Maximum query response time:

 

LTP-8X(switch)(config-vlan)# ip igmp query-response-interval 10

 

Interval between Group-Specific Queries: 

LTP-8X(switch)(config-vlan)# ip igmp last-member-query-interval 1

 

Robustness:

 

LTP-8X(switch)(config-vlan)# ip igmp robustness 2

 

Step 7. 

Disable MLD snooping by using the 

no ipv6 mld snooping enable

 command if needed.

 

Summary of Contents for LTP-4X








































































































































































































Reviews:

No comments

Related manuals for LTP-4X

National Instruments Module NI PXI-8250 User Manual preview
Module NI PXI-8250
Brand: National Instruments Pages: 39
Salto Node Installation Manual preview
Node
Brand: Salto Pages: 2
DPtech LSW3003 Series Manual preview
LSW3003 Series
Brand: DPtech Pages: 39
KPN MIK820 Quick Start Manual preview
MIK820
Brand: KPN Pages: 14
LSI MegaRAID SCSI 320-2X Quick Installation Manual preview
MegaRAID SCSI 320-2X
Brand: LSI Pages: 4
ekwb EK-FC Installation Manual preview
EK-FC
Brand: ekwb Pages: 2
APARIAN DH485 Quick Start Manuals preview
DH485
Brand: APARIAN Pages: 2
Longshine LCS-8131G3 User Manual preview
LCS-8131G3
Brand: Longshine Pages: 27
Brocade Communications Systems NetIron MLXe Series Hardware Installation Manual preview
NetIron MLXe Series
Brand: Brocade Communications Systems Pages: 305
Bridgeworks Oresund EFC102200 User Manual preview
Oresund EFC102200
Brand: Bridgeworks Pages: 84
Accton Technology MR3202A User Manual preview
MR3202A
Brand: Accton Technology Pages: 78
mikroElektronika Pressure click Quick Start Manual preview
Pressure click
Brand: mikroElektronika Pages: 2
ICP Chapter C Quick Setup Manual preview
Chapter C
Brand: ICP Pages: 68
Hama 00176547 Operating Instruction preview
00176547
Brand: Hama Pages: 25
Infoblox Infoblox-250 Installation Manual preview
Infoblox-250
Brand: Infoblox Pages: 16
Navitar 1-62643 Dimensional Drawing preview
1-62643
Brand: Navitar Pages: 1
Matrix Switch Corporation MSC-CP16X4E Product Manual preview
MSC-CP16X4E
Brand: Matrix Switch Corporation Pages: 48
Intel 80960KB Manual preview
80960KB
Brand: Intel Pages: 44

Brands by name

Popular brands

Load more brands