manualshive.com logo in svg

ELTEX LTP-4X, Operation Manual

The ELTEX LTP-4X Operation Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines for seamless operation of your ELTEX LTP-4X device. Visit our website to access the manual and make the most of your product's capabilities.

Share
Download
background image

 

45 

 
        6               view-gpon, view-ont 
                        view-ont-profile, config-gpon 
                        ont-operation, config-ont-profile 
 
        7               view-switch, view-gpon 
                        view-ont, view-ont-profile 
                        view-switch-interfaces 
 
        8               view-switch, view-gpon 
                        view-ont, view-ont-profile 
                        view-switch-interfaces, config-switch 
                        config-switch-interfaces 
 
        9               view-switch, view-gpon 
                        view-ont, view-ont-profile 
                        view-switch-interfaces, config-switch 
                        config-gpon, config-ont 
                        ont-operation, config-ont-profile 
                        config-switch-interfaces 
 
        10              view-switch, view-alarm 
                        view-system, view-general 
                        view-gpon, view-ont 
                        view-ont-profile, view-switch-interfaces 
 
        11              view-switch, view-alarm 
                        view-system, view-general 
                        view-gpon, view-ont 
                        view-ont-profile, view-switch-interfaces 
                        config-alarm, config-system 
                        config-general 
 
        12              view-switch, view-alarm 
                        view-system, view-general 
                        view-gpon, view-ont 
                        view-ont-profile, view-switch-interfaces 
                        config-switch, config-alarm 
                        config-system, config-general 
                        config-switch-interfaces 
 
        13              view-gpon, view-ont 
                        view-ont-profile 
 
        14              --- 
 
        15              view-switch, view-alarm 
                        view-system, view-general 
                        view-gpon, view-ont 
                        view-ont-profile, view-switch-interfaces 
                        config-switch, config-alarm 
                        config-system, config-general 
                        config-gpon, config-ont 
                        ont-operation, config-ont-profile 
                        config-switch-interfaces 

Step 2. 

Switch to the 

configure

 view. Set the required permissions corresponding to the level by using the 

privilege

 command, e. g. set permissions allowing Level 1 to view configuration of the internal switch:

 

LTP-8X# configure terminal 
LTP-8X(config)# privilege 1 view-switch 

 

 

Summary of Contents for LTP-4X








































































































































































































Reviews:

No comments

Related manuals for LTP-4X

Cabletron Systems Netlink FRX4000 Installation And Setup Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 8
Cabletron Systems 9C300-1 Upgrade Instructions preview
9C300-1
Brand: Cabletron Systems Pages: 4
Cabletron Systems MMAC-Plus 9F106-02 Reference Manual preview
MMAC-Plus 9F106-02
Brand: Cabletron Systems Pages: 7
MA lighting grandMA2 Series Quick Manual preview
grandMA2 Series
Brand: MA lighting Pages: 36
Juniper TX MATRIX PLUS Hardware Manual preview
TX MATRIX PLUS
Brand: Juniper Pages: 502
Blackrock Microsystems Cerebus Instructions For Use Manual preview
Cerebus
Brand: Blackrock Microsystems Pages: 27
AMD SB710 User Manual preview
SB710
Brand: AMD Pages: 20
AXIOMTEK AIE900-XNX Series User Manual preview
AIE900-XNX Series
Brand: AXIOMTEK Pages: 53
S&T kontron KBox E-420-R1K/V1K User Manual preview
kontron KBox E-420-R1K/V1K
Brand: S&T Pages: 82
Daedalon EC-33 Instruction Manual preview
EC-33
Brand: Daedalon Pages: 6
Brocade Communications Systems NetIron MLXe Series Hardware Installation Manual preview
NetIron MLXe Series
Brand: Brocade Communications Systems Pages: 305
HighPoint RocketCache 3240X8 User Manual preview
RocketCache 3240X8
Brand: HighPoint Pages: 17
AXAGO PCEU-43R Quick Installation Manual preview
PCEU-43R
Brand: AXAGO Pages: 2
ZyXEL Communications G-170S User Manual preview
G-170S
Brand: ZyXEL Communications Pages: 79
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Brand: Patton electronics Pages: 145
Navitar 1-62645 Dimensional Drawing preview
1-62645
Brand: Navitar Pages: 1
Advantech PPC-3211W User Manual preview
PPC-3211W
Brand: Advantech Pages: 66
Rockwell Automation Trusted T8833 Manual preview
Trusted T8833
Brand: Rockwell Automation Pages: 21

Brands by name

Popular brands

Load more brands