ELTEX LTP-4X Operation Manual Download Page 54

Page: 54 / 199

Step 5.

Check the entered data by using the

do show ip ntp

command.

LTP-8X(config)# do show ip ntp
  Ntp:
  Enabled: true
  Ntpserver: 192.168.1.254
  Interval: 3600
  Timezone: 7
  Daylightsaving: true

LTP-8X(config)#

Step 6.

Apply the configuration by using the

commit

command.

LTP-8X(config)# do commit

14.3

ACSD and DHCPD Configuration

The terminal has an integrated auto configuration server (ACS)

. To ensure interaction between ONTs and

ACS, ONTs should obtain IP addresses for their management interfaces. The terminal has an integrated DHCP
server to solve this task. These two servers are interconnected and cannot work separately.

14.3.1

ACSD Configuration

Step 1.

Switch to the

configure

view.

LTP-8X# configure terminal

Step 2.

Turn on the ACS server by using the

ip acs server enable

command.

LTP-8X(config)# ip acs server enable

Step 3.

If necessary, set the IP address, server mask, and identifier of the management VLAN, which will

be used to send packets between ACS and ONTs. By default, mask 21 is set, which enables 2,046 hosts per
network.

LTP-8X(config)# ip acs server ip 192.168.200.9
LTP-8X(config)# ip acs server mask 255.255.255.0
LTP-8X(config)# ip acs server vid 200

Step 4.

In addition to HTTP, ACS can also use an extended version of this protocol that supports

encryption—HTTPS. This is configured by the

ip acs server scheme

command:

LTP-8X(config)# ip acs server scheme http

Step 5.

If necessary, configure the login and password to be used by ONTs to access the ACS server:

This is actual for LTP-4/8X rev. B and LTP-4/8X rev. C only.

Summary of Contents for LTP-4X








































































































































































































Search results

Summary of Contents for LTP-4X

Reviews:

Related manuals for LTP-4X

Brands by name

Popular brands

ELTEX LTP-4X, Operation Manual

Search results

Summary of Contents for LTP-4X

Reviews:

Related manuals for LTP-4X

Brands by name

Popular brands