manualshive.com logo in svg

Dräger Narkomed 2B, Service Manual, Page: 99 / 308

Share
Download
Dräger Narkomed 2B Service Manual Download Page 99

NM2B

REPLACEMENT PROCEDURES (continued)

4.19.42 Remove the muffler/silencer (white tube) from the intake flange at

the interface wall by turning the muffler counter-clockwise.

4.19.43 Disconnect the press-on clamp and small diameter tubing from the

left side hose barb on the ventilator solenoid valve (port labeled
"out").

4.19.44 Disconnect the compression fitting at the outboard end of the copper

tube from the valve case assembly.

4.19.45 Unscrew the bellows adjustment rod tube from the top of the

assembly. Do not misplace the spacer ring.

4.19.46 Pull the bellows adjustment rod up.

4.19.47 Remove the two screws securing the valve case and guide assembly

to the bellows top plate.

NOTE:

Be careful not to misplace the two O-rings and the spacer
ring under the valve case assembly.

4.19.48 Pull both large diameter tubes forward until they clear the muffler

housing interface wall.

4.19.49 Rotate the valve case and guide assembly as needed in order to

withdraw it from the bellows box.

CAUTION: Do not damage any of the fittings or small hose barbs on

the assembly during its removal.

4.19.50 Transfer the large diameter tubing and hose clamps to the intake and

exhaust ports on the replacement valve case and guide assembly.

4.19.51 Carefully position the replacement valve case and guide assembly in

the bellows box, with the copper tube extending up into the ventilator
box, and with the intake and exhaust hoses correctly positioned in the
muffler housing interface wall.

4.19.52 Secure the valve case assembly to the bellows top plate with the two

screws that were previously removed. Be sure that the spacer ring
and the two O-rings in the bellows top plate are properly seated.

Rev. A

4-67

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Narkomed 2B





















































































































































































































































































































Reviews:

No comments