Home
/
Dräger
/
Narkomed 2B
/
Service Manual

Dräger Narkomed 2B, Service Manual, Page: 107 / 308

Share

Page: 107 / 308

Dräger Narkomed 2B Service Manual Download Page 107

NM2B

REPLACEMENT PROCEDURES (continued)

4.21.10 Remove the alarm channel mounting screws. If the machine does not

have an auxillary O

2

flow meter, skip the next two steps.

4.21.11 If the machine is equipped with an auxillary O

2

flow meter,pull the

alarm channel forward far enough to gain access to the system power
switch valve, cut the tie-wrap clamp on the flexible tube at the valve,
and remove the tube from the valve.

4.21.12 Connect the flexible tube to the system power switch valve on the

replacement alarm channel and install a new tie-wrap clamp.

4.21.13 Set the replacement alarm channel in position and connect the two

compression fittings to the system power switch valve. Do not tighten
the fittings yet.

4.21.14 Reinstall the alarm channel mounting screws.

4.21.15 Feed the flowmeter lights wire harness connector through the hole at

the top of the alarm channel.

4.21.16 Reinstall the cover plate at the top of the channel and secure it with

the hardware that was previously removed.

4.21.17 Tighten the two compression fittings at the system power switch

valve and perform the following leak test:

4.21.17.1

Open the oxygen cylinder valve and allow the pressure to
stabilize.

4.21.17.2

Close the oxygen cylinder valve.

4.21.17.3

The pressure should not drop more than 50 psi in two
minutes. (The cylinder pressure must be at least 1000
psi for this test.)

4.21.18 Connect the cables that were previously removed from J1, J2, J3 and

J4 on the alarm circuit board.

4.21.19 Replace the rear cover and its retaining screws.

4.21.20 Replace the table top and its mounting screws.

4.21.21 Connect the pipeline hoses and restore AC power to the machine.

4.21.22 Perform the PMS Procedure given in Section 6.

Rev. A

4-75

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

«
...
105
106
107
108
109
...
»

Summary of Contents for Narkomed 2B





















































































































































































































































































































Reviews:

No comments