manualshive.com logo in svg

Dräger Narkomed 2B, Service Manual, Page: 88 / 308

Share
Download
Dräger Narkomed 2B Service Manual Download Page 88

REPLACEMENT PROCEDURES (continued)

NM2B

4.18

AV-E Inspiratory Flow Regulator

The inspiratory flow regulator is located in the ventilator box. Access to the
regulator requires removal of the ventilator box front panel, and lifting the
monitor box. Figure 4-18 shows the regulator mounting arrangement and its
connections.

4.18.1

Set the System Power switch to

STANDBY

.

4.18.2

Remove the four screws holding the ventilator box front panel.
Remove the panel and carefully separate the ventilator switch in-line
connector.

4.18.3

Remove the screws holding the monitor box to the ventilator box.

WARNING:

Two people are required to perform the remaining
portion of this procedure.

4.18.4

Raise the front of the monitor box chassis approximately four inches,
and prop the box open.

WARNING:

Ensure that AC power is removed from the
machine before raising the monitor box. Failure to
observe this precaution may cause injury by
electric shock.

4.18.5

Disconnect the two compression fittings at the regulator.

4.18.6

Remove the tie strap securing the small diameter flex tubing to the
hose barb on the flow regulator assembly, and disconnect the tubing.

4.18.7

Un-screw the retaining ring holding the regulator to its mounting
bracket, and remove the regulator.

4.18.8

Install the replacement regulator in the mounting bracket and
tighten the mounting ring.

4.18.9

Connect the two compression fittings to the regulator.

4.18.10 Reattach the small diameter flex tubing previously removed from the

regulator assembly and secure the connection with a tie strap.

4.18.11 Remove the prop from the front of the monitor box, and return the

box to its normal position.

4.18.12 Replace the four screws holding the monitor box to the ventilator box.

4-56

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Narkomed 2B





















































































































































































































































































































Reviews:

No comments