manualshive.com logo in svg

Dräger Narkomed 2B, Service Manual, Page: 87 / 308

Share
Download
Dräger Narkomed 2B Service Manual Download Page 87

NM2B

REPLACEMENT PROCEDURES (continued)

4.17.6

Unscrew the two hex post nuts holding the filter to the ventilator box,
and remove the filter.

4.17.7

Install the replacement filter and secure it with the two hex post
nuts.

4.17.8

Connect the AC wiring to the replacement filter. Be sure to observe
the wire color code as illustrated.

4.17.9

Place the safety cover over the filter and secure it with the two
screws.

4.17.10 Remove the prop from the rear of the monitor box, and return the box

to its normal position.

4.17.11 Replace the screws holding the monitor box to the ventilator box.

4.17.12 Restore power to the machine and perform the PMS Procedure given

in Section 6.

Rev. A

4-55

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Narkomed 2B





















































































































































































































































































































Reviews:

No comments