manualshive.com logo in svg

Dräger Narkomed 2B, Service Manual, Page: 42 / 308

Share
Download
Dräger Narkomed 2B Service Manual Download Page 42

REPLACEMENT PROCEDURES (continued)

NM2B

4.3.13

Connect and tighten the compression fittings at points marked

C

on

the illustration.

4.3.14

Perform the following test: --Remove the plug from the test gauge
connection at the Tee fitting in the regulator outlet piping, and install
a test gauge.

NOTE:

The cylinders used for this test must contain the following minimum
pressure:

O

2

: 1000 PSI

AIR

: 1000 PSI

O

2

+He : 1000 PSI

N

2

O

: 745 PSI

--Set the System Power switch to ON.

--For the O

2

cutoff valve: open the O

2

cylinder valve and set the oxygen flow to

4 liters per min.

--For the N

2

O cutoff valve: open the O

2

cylinder valve and the N

2

O cylinder

valve. Set each flow to 4 liters per min.

--Verify that regulator outlet pressure is between 43 and 49 PSI.

--Connect the pipeline hoses and pressurize to 50 PSI.

--Turn off the pipeline supply and observe the pipeline pressure gauge.

--The cutoff valve shall open when the pipeline pressure drops through the

range of 45 to 40 PSI.

--Close the cylinder valve(s), and close the flow control valve(s).

--Disconnect test pressure gauge and reinstall the plug in the regulator outlet

piping.

4.3.15

Replace the table top and its retaining screws.

4.3.16

Replace the top drawer in the cabinet.

4.3.17

Connect the pipeline hoses.

4.3.18

Perform the PMS Procedure given in Section 6.

O

2

Flow Test:

--Disconnect all pipeline supplies.

--Install a full O

2

cylinder on the machine, and open the cylinder valve.

--Turn the System Power switch to ON.

--Set the Inspiratory Flow control to maximum high, and turn the ventilator switch to ON.

--Set the oxygen flow to 10 l/min.

--Verify that the oxygen flow does not drop below 8 l/min. while the ventilator is running.

--Press and hold the O

2

FLUSH button while observing the O

2

flowmeter, and verify that the

oxygen flow does not drop below 8 l/min.

--If the oxygen flow in either of the above two steps drops below 8 l/min., replace the O

2

cutoff

valve assembly.

Rev. D

4-10

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Narkomed 2B





















































































































































































































































































































Reviews:

No comments