manualshive.com logo in svg

Dräger Narkomed 2B, Service Manual, Page: 104 / 308

Share
Download
Dräger Narkomed 2B Service Manual Download Page 104

REPLACEMENT PROCEDURES (continued)

NM2B

NOTE:

If components are removed from the support plate, be sure that any
spacers and O-rings are correctly positioned during reinstallation.

4.20.14 Following component replacement, position the support plate in the

bellows box and reconnect the large and small diameter tubing that
was previously removed.

4.20.15 Slide the support plate up and to the rear until it is seated properly

in the bellows box.

4.20.16 Reinstall the two front support plate screws, and tighten the rear

support plate screw.

4.20.17 Install the volume indicator on the bellows adjustment rod in the

same position as before disassembly, and tighten its two setscrews.

4.20.18 Install the bellows guide by screwing its stem into the bellows

adjustment rod.

4.20.19 Place the bellows box front panel into position, ensure that the slots

in the knob assemblies are correctly aligned with their drive pins on
the bellows adjustment and pressure limit control shafts, and
reinstall the screws holding the front panel to the machine.

4.20.20 Replace the bellows canister; ensure that its markings are facing

forward.

4.20.21 Replace the bellows assembly and tighten the wing nuts holding it in

place.

4.20.22 Reconnect any hoses that were previously removed from the bellows

assembly.

4.20.23 Reconnect the pipeline hoses and AC power cord.

4.20.24 Perform the PMS Procedure given in Section 6.

Rev. A

4-72

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Narkomed 2B





















































































































































































































































































































Reviews:

No comments