manualshive.com logo in svg

Dräger Narkomed 2B, Service Manual, Page: 64 / 308

Share
Download
Dräger Narkomed 2B Service Manual Download Page 64

REPLACEMENT PROCEDURES (continued)

NM2B

4.10.14 Connect the flexible N

2

O tubing that was removed in the previous

step to the tee fitting at the front of the replacement ORMC, and
secure the connection with a new tie strap clamp. (Later models do
not have the tee fitting.)

4.10.15 Connect the copper N

2

O lines to the replacement ORMC and tighten

the compression fittings.

*

4.10.16 Join the in-line wiring harness to the replacement ORMC connectors

and install a new tie-wrap cable clamp.

4.10.17 Connect the flexible O

2

tubing to the left side of the ORMC, and

connect the flexible N

2

O tubing to right side of the MPL switch.

Secure each connection with a press-on clamp. (Later models do not
have the MPL switch.)

4.10.18 Open the O

2

and N

2

O cylinder valves.

4.10.19 Set the System Power switch to ON, and perform the following test:

4.10.19.1

Open the N

2

O flow control valve three turns. There

should be no nitrous oxide flow.

4.10.19.2

Slowly open the O

2

flow control valve. The nitrous oxide

should start to flow when the oxygen flow is between 200
and 300 ml per minute.

4.10.19.3

Connect a calibrated oxygen monitor to the Freshgas
Outlet.

4.10.19.4

Adjust the oxygen flow to 1 liter per minute. The oxygen
concentration should be between 21% and 29% oxygen.

*

4.10.19.5

The yellow O

2

/N

2

O FLOW RATIO lamp on the alarm

panel should be lighted.

4.10.19.6

Adjust the oxygen flow to 1.5 liters per minute. The
oxygen concentration should be between 21% and 29%
oxygen.

*

4.10.19.7

The yellow O

2

/N

2

O FLOW RATIO lamp on the alarm

panel should be lighted.

4.10.19.8

Adjust the oxygen flow to a point where the nitrous oxide
flowmeter indicates 10 liters per minute.

Rev. A

4-32

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Narkomed 2B





















































































































































































































































































































Reviews:

No comments