Dräger Narkomed 2B Service Manual Download Page 212

Page: 212 / 308

PMC PROCEDURE (continued)

NM2B

6.14.6

Helium O.F.P.D. - if applicable

6.14.6.1

Set the gas selector switch to ALL GASES.

6.14.6.2

Open the helium cylinder valve.

6.14.6.3

Open one (1) oxygen cylinder valve.

6.14.6.4

Set the helium flow to 4 l/min; set the oxygen flow to 4 l/min.

6.14.6.5

Close the oxygen cylinder valve.

( )

6.14.6.6

Does the flow of helium cease when the oxygen pressure is
depleted? ___ (Y)

6.14.6.7

Close the helium flow control valve.

6.14.6.8

Set the gas selector switch to O

+ N

6.14.6.9

Close the oxygen flow control valve.

6.14.7

Oxygen Supply Pressure Alarm

6.14.7.1

If not already connected, connect a dedicated O

test gauge to the

TEE fitting in the O

regulator output line.

6.14.7.2

Open and close an oxygen cylinder.

6.14.7.3

Set the oxygen flow to 2 l/min.

( )

6.14.7.4

What is the pressure on the dedicated O

test gauge when the "O2

SUPPLY PRESSURE" LED turns on? ___ PSI (34 - 40)

6.14.7.5

Does the O2 SUPPLY LOW message appear in the Caution
display? ___ (Y)

6.14.7.6

Bleed the remaining O

pressure from the system, then close the

flow control valve.

6.14.7.7

Remove the test gauge from the TEE fitting in the O

regulator

output line and replace the plug.

Rev. Y

6-34

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Narkomed 2B





















































































































































































































































































































Search results

Summary of Contents for Narkomed 2B

Reviews:

Dräger Narkomed 2B, Service Manual, Page: 212 / 308

Search results

Summary of Contents for Narkomed 2B

Reviews: