Dräger Narkomed 2B Service Manual Download Page 216

Page: 216 / 308

PMC PROCEDURE (continued)

NM2B

6.16 O2 MED

6.16.1

Disconnect the O

sensor cable from the oxygen sensor interface.

6.16.2

The following messages shall appear on the display: "O

SENS DISC",

NOT CAL", "O

ALRM OFF".

6.16.3

Reconnect the O

Med sensor.

6.16.4

The "O

SENS DISC" message shall disappear.

6.16.5

Press the "21%" key to calibrate the O

Med.

NOTE:

Make sure the sensor is stabilized in ambient air for several minutes.

( )

6.16.6

After the calibration is completed, what is the oxygen concentration?
___ % (21)

6.16.7

This step intentionally left blank.

6.16.8

The alarm CRT shall display "% OXYGEN LOW" under the warning
heading. There should be a continuous audible alarm.

6.16.9

What is the low oxygen alarm default? ___ % (30)

6.16.10

This step intentionally left blank.

6.16.11

Press the LO oxygen alarm key. Does a box appear around the low
alarm limit? ___ (Y)

6.16.12

Verify that the low alarm limit has a range from 21 to 99% (18 to 99%
with firmware version 2.03 and later).

6.16.13

Place the sensor into the inspiratory valve dome adapter. Set the
Man/Auto selector to BAG, close the APL valve, attach a 12-inch hose
to the inspiratory valve, and occlude the bag mount.

6.16.14

Set the oxygen flow to 4 l/min.

6.16.15

Set the low limit to the lowest setting possible, and verify the "%
OXYGEN LOW" message has cleared.

6.16.16

Press the HI oxygen alarm key. Does a box appear around the high
alarm limit? ___(Y)

Rev. Y

6-38

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Narkomed 2B





















































































































































































































































































































Search results

Summary of Contents for Narkomed 2B

Reviews:

Dräger Narkomed 2B, Service Manual, Page: 216 / 308

Search results

Summary of Contents for Narkomed 2B

Reviews: