Dodge 2011 Challenger SRT Owner'S Manual Download Page 263

Page: 263 / 459

CAUTION!

•

If you skip more than one gear while downshift-
ing or downshift at too high an engine speed, you
could damage the engine, transmission, or clutch.

•

Do not downshift into first gear when the vehicle
is moving faster than 15 mph (24 km/h), as you
could damage the engine and/or clutch.

AUTOMATIC TRANSMISSION — IF EQUIPPED

CAUTION!

Damage to the automatic transmission may occur if
the following precautions are not observed:

•

Shift into PARK only after the vehicle has come to
a complete stop.

(Continued)

CAUTION! (Continued)

•

Shift into or out of REVERSE only after the
vehicle has come to a complete stop and the engine
is at idle speed.

•

Do not shift from REVERSE, PARK, or NEUTRAL
into any forward gear when the engine is above
idle speed.

•

Before shifting into any gear, make sure your foot
is firmly on the brake pedal.

STARTING AND OPERATING

261

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Search results

Summary of Contents for 2011 Challenger SRT

Reviews:

Related manuals for 2011 Challenger SRT

Brands by name

Popular brands

Dodge 2011 Challenger SRT, Owner'S Manual

Search results

Summary of Contents for 2011 Challenger SRT

Reviews:

Related manuals for 2011 Challenger SRT

Brands by name

Popular brands