manualshive.com logo in svg

Dodge 2011 Challenger SRT, Owner'S Manual

The Dodge 2011 Challenger SRT is a powerful and stylish car that combines classic muscle car design with modern performance. To fully understand and maximize the potential of this exceptional vehicle, it is crucial to have the Owner's Manual. You can conveniently download the manual for free from manualshive.com, ensuring a seamless and enjoyable ownership experience.

Share
Download
background image

2. Place the handheld transmitter 1 to 3 in (3 to 8 cm)
from the HomeLink

威

buttons while keeping the EVIC

display in view.

For optimal training, point the battery end of the hand-
held transmitter away from the HomeLink

威

.

3. Simultaneously, press and hold both the chosen
HomeLink

威

button and the handheld transmitter button

until the EVIC display changes from “CHANNEL #
TRAINING” to “CHANNEL # TRAINED.”

Then release both the HomeLink

威

and handheld trans-

mitter buttons.

If the EVIC display states “DID NOT TRAIN” repeat
Step 3. If the signal is too weak, replace the battery in the
handheld transmitter.

It may take up to 30 seconds or longer in rare cases. The
garage door may open and close while you train.

NOTE:

Some gate operators and garage door openers

may require you to replace Step 3 with procedures noted
in the “Gate Operator/Canadian Programming” section.

4. Press and hold the just-trained HomeLink

威

button. If

the channel has been trained, the EVIC display will now
state “CHANNEL # TRANSMIT.”

If the EVIC display still states “CHANNEL # TRAIN-
ING” repeat Step 3.

NOTE:

After training a HomeLink

威

channel, if the

garage door does not operate with HomeLink

威

and the

garage door opener was manufactured after 1995, the
garage door opener may have rolling code. If so, proceed
to Step 5.

5. Programming A Rolling Code System

At the garage door opener motor (in the garage), locate
the “learn” or “training” button.

154

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger SRT

A-Tach Mounts ST-1 Instructions preview
ST-1
Brand: A-Tach Mounts Pages: 2
A-Tach Mounts 50291 Quick Start Manual preview
50291
Brand: A-Tach Mounts Pages: 2
A-Tach Mounts 50206 Instructions preview
50206
Brand: A-Tach Mounts Pages: 2
Paccar DAF POWERCHOICE 250A Installation Manual preview
DAF POWERCHOICE 250A
Brand: Paccar Pages: 20
Kolpin 25-9250 Owner'S And Operator'S Manual preview
25-9250
Brand: Kolpin Pages: 25
BrandMotion 1009-6503 Installation Instructions Manual preview
1009-6503
Brand: BrandMotion Pages: 8
Chevrolet 2013 Spark Specifications preview
2013 Spark
Brand: Chevrolet Pages: 2
Kargo Master 4A82T Installation Manual preview
4A82T
Brand: Kargo Master Pages: 6
Cadillac Escalade ESV 2014 Owner'S Manual preview
Escalade ESV 2014
Brand: Cadillac Pages: 508
Hama Liberty III Quick Start Manual preview
Liberty III
Brand: Hama Pages: 2
Fiat Fiat Bravo LPG Owner'S Manual preview
Fiat Bravo LPG
Brand: Fiat Pages: 24
Valeo AS1A Owner'S Manual preview
AS1A
Brand: Valeo Pages: 28
THIEYE CarView 2 User Manual preview
CarView 2
Brand: THIEYE Pages: 88
Oldsmobile 1995 Cutlass Supreme Owner'S Manual preview
1995 Cutlass Supreme
Brand: Oldsmobile Pages: 340
iDataLink ADS-TBSL-GM Install Manual preview
ADS-TBSL-GM
Brand: iDataLink Pages: 6
Voxx Electronics CA-510a Installation Instructions Manual preview
CA-510a
Brand: Voxx Electronics Pages: 15
Mobileye C2-270 User Manual preview
C2-270
Brand: Mobileye Pages: 29
SMART EQ forfour 2018 Owner'S Manual preview
EQ forfour 2018
Brand: SMART Pages: 224

Brands by name

Popular brands

Load more brands