manualshive.com logo in svg

Dodge 2011 Challenger SRT, Owner'S Manual

The Dodge 2011 Challenger SRT is a powerful and stylish car that combines classic muscle car design with modern performance. To fully understand and maximize the potential of this exceptional vehicle, it is crucial to have the Owner's Manual. You can conveniently download the manual for free from manualshive.com, ensuring a seamless and enjoyable ownership experience.

Share
Download
background image

NOTE:

If the Mode Select Knob (5) is on Air Mode and

the pump is operating, air will dispense from the Air
Pump Hose (7) only, not the Sealant Hose (6).

If the sealant (white fluid) does flow

through the

Sealant Hose (6):

1. Continue to operate the pump until sealant is no
longer flowing through hose (typically takes 30 - 70 sec-
onds). As the sealant flows through the Sealant Hose (6),
the Pressure Gauge (3) can read as high as 70 psi (5 Bar).
The Pressure Gauge (3) will decrease quickly from ap-
proximately 70 psi (5 Bar) to the actual tire pressure when
the Sealant Bottle (1) is empty.

2. The pump will start to inject air into the tire immedi-
ately after the Sealant Bottle (1) is empty. Continue to
operate the pump and inflate the tire to the pressure
indicated on the tire pressure label on the driver-side
latch pillar (recommended pressure). Check the tire pres-
sure by looking at the Pressure Gauge (3).

If the tire does not inflate to at least 26 psi (1.8 Bar)
pressure within 15 minutes:

•

The tire is too badly damaged. Do not attempt to drive
the vehicle further. Call for assistance.

NOTE:

If the tire becomes over-inflated, press the

Deflation Button to reduce the tire pressure to the recom-
mended inflation pressure before continuing.

If the tire inflates to the recommended pressure or is at
least 26 psi (1.8 Bar) pressure within 15 minutes:

1. Press the Power Button (4) to turn off the TIREFIT kit.

2. Remove the Speed Limit sticker from the top of the
Sealant Bottle (1) and place the sticker on the instrument
panel.

3. Immediately disconnect the Sealant Hose (6) from the
valve stem, reinstall the cap on the fitting at the end of the

6

WHAT TO DO IN EMERGENCIES

339

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger SRT

Pontiac 2004 Vibe Navigation System Owner'S Manual preview
2004 Vibe Navigation System
Brand: Pontiac Pages: 44
Rati Armster 2 User Manual preview
Armster 2
Brand: Rati Pages: 2
PAC Stinger ELEV8 Install Manual preview
Stinger ELEV8
Brand: PAC Pages: 14
Kolpin 98310 Product Instructions preview
98310
Brand: Kolpin Pages: 3
AEM 30-3500 Instruction Manual preview
30-3500
Brand: AEM Pages: 27
TAUBENREUTHER 16-5911 Manual preview
16-5911
Brand: TAUBENREUTHER Pages: 18
Toro Security Cage Kit Installation Instructions Manual preview
Security Cage Kit
Brand: Toro Pages: 8
GROM Audio VLINE Installation Manual preview
VLINE
Brand: GROM Audio Pages: 20
Bracketron Multi Vehicle Mount MVM-35-05 Installation Manual preview
Multi Vehicle Mount MVM-35-05
Brand: Bracketron Pages: 4
Chevrolet 1995 C/K Pickup Owner'S Manual preview
1995 C/K Pickup
Brand: Chevrolet Pages: 483
HOLDEN Malibu EM 2015 Owner'S Handbook Manual preview
Malibu EM 2015
Brand: HOLDEN Pages: 330
Velleman CAMSET28 User Manual preview
CAMSET28
Brand: Velleman Pages: 17
RAWLINK 36772 Instruction Manual preview
36772
Brand: RAWLINK Pages: 25
TigerTough E82201B Installation Manual preview
E82201B
Brand: TigerTough Pages: 7
NavInc USB-PEU-RD4 User Manual preview
USB-PEU-RD4
Brand: NavInc Pages: 5
AA Products RB0008 Instruction Manual preview
RB0008
Brand: AA Products Pages: 6
Jeep GRAND CHEROKEE L 2021 Owner'S Manual preview
GRAND CHEROKEE L 2021
Brand: Jeep Pages: 388
LAS 105- 35PP Installation And Operating Instructions preview
105- 35PP
Brand: LAS Pages: 4

Brands by name

Popular brands

Load more brands