Dodge 2011 Challenger SRT Owner'S Manual Download Page 176 | Manualshive

Page: 176 / 459

background image

INSTRUMENT CLUSTER DESCRIPTIONS

1. Fuel Gauge

The pointer shows the level of fuel in the fuel tank when
the ignition switch is in the ON/RUN position.

2. Trip Odometer Button

Press this button to change the display from odometer to
either of two trip odometer settings. The letter “A” or “B”
will appear when in the trip odometer mode. Push in and
hold the button for two seconds to reset the trip odometer
to 0 miles (km). The odometer must be in TRIP mode to
reset it.

3. Speedometer

Indicates vehicle speed.

4. Electronic Speed Control Indicator Light

This light will turn on when the electronic
speed control is on.

5. Tachometer

The red segments indicate the maximum permissible
engine revolutions per minute (RPM x 1000) for each gear
range. Ease up on the accelerator before reaching the red
area.

6. Charging System Warning Light

This light shows the status of the electrical charg-
ing system. The light should turn on when the

ignition switch is first placed in ON/RUN and remain on
briefly as a bulb check. If the light stays on or turns on
while driving, turn off some of the vehicle’s non-essential
electrical devices (i.e., radio) or slightly increase engine
speed (if at idle). If the light remains on, it means that the
charging system is experiencing a problem. See your
local authorized dealer to obtain service immediately.

If jump starting is required, refer to “Jump Starting
Procedures” in “What To Do In Emergencies”.

174

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
174
175
176
177
178
...
»

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger SRT

Titanium Series

Brand: Fass Pages: 13

Brand: Mobis Pages: 16

Brand: Subaru Pages: 216

Brand: FORM FIT Pages: 2

2014 Grand Cherokee SRT8

Brand: Jeep Pages: 596

Brand: Skoda Pages: 4

Brand: r.LiNK Pages: 21

Brand: Quadratec Pages: 2

Brand: Saab Pages: 9

Brand: WABCO Pages: 40

Brand: Kargo Master Pages: 7

Brand: Fortin Electronic Systems Pages: 5

Brand: GStop Pages: 28

Brand: Chevrolet Pages: 6

Brand: 3UVIEW Pages: 15

Brand: Fyndr Pages: 20

GRAND CHEROKEE L 2021

Brand: Jeep Pages: 388

Brand: Geely Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands