Dodge 2011 Challenger SRT Owner'S Manual Download Page 35 | Manualshive

Page: 35 / 459

background image

•

For vehicles not equipped with the EVIC, perform the
following procedure:

1. Close all doors and place the key in the ignition
switch.

2. Within 15 seconds, cycle the ignition switch between
LOCK and ON/RUN and then back to LOCK four times
ending up in the LOCK position (do not start the engine).

3. Within 30 seconds, press the power door LOCK switch
to lock the doors.

4. A single chime will indicate the completion of the
programming.

5. Repeat these steps if you want to return this feature to
its previous setting.

NOTE:

•

If you do not hear the chime it means that the system
did not enter the programming mode and you will
need to repeat the procedure.

•

Use the Automatic Door Locks feature in accordance
with local laws.

Automatic Unlock Doors On Exit

The doors will unlock automatically if:

1. The Automatic Unlock Doors On Exit feature is en-
abled

2. The transmission was in gear and the vehicle speed
returned to 0 mph (0 km/h)

3. The transmission is in NEUTRAL or PARK

4. The driver door is opened

5. The doors were not previously unlocked

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

33

«
...
33
34
35
36
37
...
»

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger SRT

Brand: JAC Pages: 70

Brand: Jeep Pages: 25

Brand: JANE Pages: 21

Brand: Lincoln Pages: 424

Brand: Volkswagen Pages: 26

Brand: Mazda Pages: 527

2008 Escalade EXT

Brand: Cadillac Pages: 496

Brand: Yakima Pages: 19

UCI-11C NTV-KIT331

Brand: Nav TV Pages: 4

Brand: Maserati Pages: 210

Brand: OnStar Pages: 22

Brand: Metra Electronics Pages: 20

StreetLine Series

Brand: SAAS Pages: 4

Brand: WABCO Pages: 52

Brand: Kia Pages: 11

Brand: Saab Pages: 426

Brand: rough country Pages: 4

Brand: TAUBENREUTHER Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands