manualshive.com logo in svg

Dodge 2011 Challenger SRT, Owner'S Manual

The Dodge 2011 Challenger SRT is a powerful and stylish car that combines classic muscle car design with modern performance. To fully understand and maximize the potential of this exceptional vehicle, it is crucial to have the Owner's Manual. You can conveniently download the manual for free from manualshive.com, ensuring a seamless and enjoyable ownership experience.

Share
Download
background image

7. Electronic Throttle Control (ETC) Warning Light

This light will turn on briefly as a bulb check
when the ignition switch is placed in ON/
RUN. This light will also turn on while the
engine is running if there is a problem with the

Electronic Throttle Control (ETC) system.

If the light comes on while the engine is running, safely
bring the vehicle to a complete stop as soon as possible,
place the shift lever in PARK, and cycle the ignition key. The
light should turn off. If the light remains lit with the engine
running, your vehicle will usually be drivable. However,
see an authorized dealer for service as soon as possible.

If the light is flashing when the engine is running,
immediate service is required. In this case, you may
experience reduced performance, an elevated/rough idle
or engine stall, and your vehicle may require towing.

Also, have the system checked by an authorized dealer if
the light does not come on during starting.

8. Temperature Gauge

The temperature gauge shows engine coolant tempera-
ture. Any reading within the normal range indicates that
the engine cooling system is operating satisfactorily.

The gauge pointer will likely indicate a higher tempera-
ture when driving in hot weather, up mountain grades,
or when towing a trailer. It should not be allowed to
exceed the upper limits of the normal operating range.

CAUTION!

Driving with a hot cooling system could damage
your vehicle. If the temperature gauge reads 240°F
(116°C) or greater, pull over and stop the vehicle. Idle
the vehicle with the air conditioner turned off until
the pointer drops back into the normal range 200–
230°F (93–110°C). If the pointer remains at 240°F
(116°C) or greater and you hear a chime, turn the
engine OFF immediately and call for service.

4

UNDERSTANDING YOUR INSTRUMENT PANEL

175

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger SRT

Happy Orange USB-C Quick Start Manual preview
USB-C
Brand: Happy Orange Pages: 2
cam HS Series Operating Manual preview
HS Series
Brand: cam Pages: 28
Jacob Jensen Electronic Parking Disc II User Manual preview
Electronic Parking Disc II
Brand: Jacob Jensen Pages: 28
Car-Interface CI-RL4-ELINK Manual preview
CI-RL4-ELINK
Brand: Car-Interface Pages: 23
RuggON VD04 Quick Start Manual preview
VD04
Brand: RuggON Pages: 2
Rightline Gear Car Top Duffle Bag Setup Manual preview
Car Top Duffle Bag
Brand: Rightline Gear Pages: 2
Renault Lodgy 2017 Driver'S Handbook Manual preview
Lodgy 2017
Brand: Renault Pages: 238
P-Invent Troller User Manual preview
Troller
Brand: P-Invent Pages: 4
Prorack K544 Fitting Instructions Manual preview
K544
Brand: Prorack Pages: 20
Hank HKWP1100-10Q User Quick Manual preview
HKWP1100-10Q
Brand: Hank Pages: 2
Yakima K1249 Instructions Manual preview
K1249
Brand: Yakima Pages: 9
Quadratec 16053.5300 Installation Manual preview
16053.5300
Brand: Quadratec Pages: 6
FVC Sprinter Side Ladder Installation Manual preview
Sprinter Side Ladder
Brand: FVC Pages: 8
Pontiac 2007 G6 Owner'S Manual preview
2007 G6
Brand: Pontiac Pages: 486
Edelbrock 5756 Installation Instructions preview
5756
Brand: Edelbrock Pages: 1
Brigade VBV-770-310 Quick Installation Manual preview
VBV-770-310
Brand: Brigade Pages: 12
Edelbrock PRO-FLO XT 3527 User Manual preview
PRO-FLO XT 3527
Brand: Edelbrock Pages: 39
Nav TV NTV-KIT850 Install Manual preview
NTV-KIT850
Brand: Nav TV Pages: 11

Brands by name

Popular brands

Load more brands