Dodge 2011 Challenger SRT Owner'S Manual Download Page 28 | Manualshive

Page: 28 / 459

background image

•

You may need to be less than 35 ft (11 m) from the
vehicle when using the RKE transmitter to turn off the
Panic Alarm due to the radio frequency noises emitted
by the system.

Programming Additional Transmitters

Programming Key Fobs or RKE transmitters may be
performed at an authorized dealer.

Transmitter Battery Replacement

The recommended replacement battery is CR2032.

NOTE:

Perchlorate Material – special handling may

apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

1. If the RKE transmitter is equipped with a screw,
remove the screw. With the RKE ransmitter buttons
facing down, use a flat blade to pry the two halves of the
RKE transmitter apart. Make sure not to damage the
elastomer seal during removal.

2. Remove and replace the battery. When replacing the
battery, match the + sign on the battery to the + sign on
the inside of the battery clip, located on the back cover.
Avoid touching the new battery with your fingers. Skin
oils may cause battery deterioration. If you touch a
battery, clean it with rubbing alcohol.

3. To reassemble the RKE transmitter case, snap the two
halves of the case together. Make sure there is an even
“gap” between the two halves. If equipped, install and
tighten the screw until snug. Test RKE transmitter
operation.

General Information

This device complies with Part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:

•

This device may not cause harmful interference.

26

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
26
27
28
29
30
...
»

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger SRT

Gemineye EC2014-C

Brand: Ecco Pages: 10

Reflex 5500 Series

Brand: Ecco Pages: 12

Brand: BrandMotion Pages: 2

Brand: Volvo Pages: 10

PRIME DESIGN HRR-369-E-UM3-96

Brand: Safe Fleet Pages: 12

Brand: Kocchi's Pages: 4

Brand: Mitsubishi Pages: 362

Brand: Renault Pages: 3699

Brand: Volvo Pages: 62

Brand: Mazda Pages: 605

Brand: Kargo Master Pages: 9

Brand: XTC Pages: 2

Sprinter Shuttle

Brand: L.A. West Pages: 30

80-485-142401-RT

Brand: Classic Accessories Pages: 14

ASENTO EV-EXP18R

Brand: ADAPT SOLUTIONS Pages: 25

2012 Patriot Series

Brand: Jeep Pages: 505

Brand: U.S. General Pages: 3

Brand: Genesis Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands