Dodge 2011 Challenger SRT Owner'S Manual Download Page 139 | Manualshive

Page: 139 / 459

background image

WARNING!

•

Be certain that the seatback is securely locked into
position. If the seatback is not securely locked into
position, the seat will not provide the proper
stability for child seats and/or passengers. An
improperly latched seat could cause serious injury.

•

The cargo area in the rear of the vehicle (with the
rear seatbacks in the locked-up or folded down
position) should not be used as a play area by
children when the vehicle is in motion. They could
be seriously injured in a collision. Children
should be seated and using the proper restraint
system.

TO OPEN AND CLOSE THE HOOD

Two latches must be released to open the hood.

1. Pull the hood release lever located under the left side
of the instrument panel.

Hood Release Lever

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

137

«
...
137
138
139
140
141
...
»

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger SRT

PICASSO XSARA DESIRE 1.6 - MESUREMENT

Brand: CITROEN Pages: 2

Brand: Sirius Satellite Radio Pages: 8

Brand: Phonocar Pages: 6

Brand: Nav TV Pages: 5

Ram Commercial2016

Brand: Dodge Pages: 675

Brand: A-Tach Pages: 2

Brand: Black Horse Off Road Pages: 7

Brand: Honda Pages: 268

Brand: Calix Pages: 4

Brand: Prorack Pages: 14

Brand: Cadillac Pages: 438

Brand: HUSKY LINERS Pages: 4

Brand: iOttie Pages: 19

Platinum Pro Plug-in

Brand: Haltech Pages: 20

ProPlus 620066V01

Brand: PAT Pages: 13

Wrangler Postal Vehicle 2017

Brand: Jeep Pages: 62

Brand: Maserati Pages: 288

Brand: MeiTrack Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands