Dodge 2011 Challenger SRT Owner'S Manual Download Page 285 | Manualshive

Page: 285 / 459

background image

Traction Control System (TCS)

This system monitors the amount of wheel spin of each
driven wheel. If wheel spin is detected, brake pressure is
applied to the slipping wheel(s) and engine power is
reduced to provide enhanced acceleration and stability.

A feature of the TCS system functions similar to a
limited-slip differential and controls the wheel spin
across a driven axle. If one wheel on a driven axle is
spinning faster than the other, the system will apply the
brake of the spinning wheel. This will allow more engine
torque to be applied to the wheel that is not spinning.
This feature remains active even if TCS and ESP are in the
“Partial Off” or “Full Off” modes. Refer to “Electronic
Stability Program (ESP)” in this section for more infor-
mation.

NOTE:

The LSD is a true LSD and the TCS function is

similar to a limited-slip differential.

Brake Assist System (BAS)

This system complements the ABS by optimizing the
vehicle braking capability during emergency braking
maneuvers. This system detects an emergency braking
situation by sensing the rate and amount of brake appli-
cation and then applies optimum pressure to the brakes.
This can help reduce braking distances.

Applying the brakes very quickly results in the best BAS
assistance. To receive the benefits of this system, you
must apply continuous brake pedal pressure during the
stopping sequence. Do not reduce brake pedal pressure
unless braking is no longer desired. Once the brake pedal
is released, the BAS is deactivated.

5

STARTING AND OPERATING

283

«
...
283
284
285
286
287
...
»

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger SRT

Brand: Metra Electronics Pages: 14

Brand: Laser Pages: 8

Brand: Warrior Winches Pages: 17

Brand: iDataLink Pages: 99

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

X-ACT CONTOUR 53491

Brand: HUSKY LINERS Pages: 2

Brand: Volvo Pages: 19

Brand: Whispbar Pages: 15

Brand: NavLinkz Pages: 21

Parrot MKi + ParrotCK3100 range LOGAN

Brand: Parrot Pages: 10

Brand: Yutrax Pages: 8

Brand: Pacbrake Pages: 6

Brand: Rugged Ridge Pages: 3

Brand: Vangear Pages: 5

Brand: Safe Fleet Pages: 20

Quantum Wash'n'Wipe N30208

Brand: National Cycle Pages: 12

Brand: A-Tach Mounts Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands