Dodge 2011 Challenger SRT Owner'S Manual Download Page 401

Page: 401 / 459

7. Push the electrical connector locking tab to the side.

8. Disconnect the electrical connector.

9. Turn the appropriate bulb and socket assembly coun-
terclockwise to remove it from the tail lamp assembly.

10. Disconnect the bulb from the socket assembly and
install the replacement bulb.

11. Reinstall the bulb and socket assembly into the tail
lamp assembly, and then turn it clockwise.

12. Reinstall the tail lamp assembly, fasteners, electrical
connector, and trunk liner.

13. Reinstall tail lamp retainer.

14. Close the trunk.

MAINTAINING YOUR VEHICLE

399

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Search results

Summary of Contents for 2011 Challenger SRT

Reviews:

Related manuals for 2011 Challenger SRT

Brands by name

Popular brands

Dodge 2011 Challenger SRT, Owner'S Manual

Search results

Summary of Contents for 2011 Challenger SRT

Reviews:

Related manuals for 2011 Challenger SRT

Brands by name

Popular brands