Dodge 2011 Challenger SRT Owner'S Manual Download Page 40 | Manualshive

Page: 40 / 459

background image

To Lock The Vehicle’s Doors

With one of the vehicle’s Passive Entry RKE transmitters
within 5 ft (1.5 m) of the driver or passenger front door
handles, press the door handle LOCK button to lock both
doors.

NOTE:

•

After pressing the door handle LOCK button, you
must wait two seconds before you can lock or unlock
the doors, using either Passive Entry door handle. This
is done to allow you to check if the vehicle is locked by
pulling the door handle, without the vehicle reacting
and unlocking.

•

The Passive Entry system will not operate if the RKE
transmitter battery is dead.

The vehicle doors can also be locked by using the RKE
transmitter lock button or the lock button located on the
vehicle’s interior door panel.

Outside Door Handle Lock Button

38

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
38
39
40
41
42
...
»

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger SRT

Brand: TATA Motors Pages: 94

Brand: GÄN Pages: 24

Brand: Yakima Pages: 8

Brand: Ranger design Pages: 22

Quantum hardcoated N30216

Brand: National Cycle Pages: 3

Speed & Route Profiler

Brand: Racelogic Pages: 24

Brand: EUFAB Pages: 4

TuneBase F8Z442

Brand: Belkin Pages: 162

Brand: Ford Pages: 8

Brand: EUFAB Pages: 18

Brand: Mercedes-Benz Pages: 24

Brand: Yakima Pages: 12

Brand: Rajant Pages: 11

Brand: Ford Pages: 2

Brand: Toyota Pages: 596

Brand: Curt Manufacturing Pages: 5

Brand: GMC Pages: 20

Brand: Valeo Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands