manualshive.com logo in svg

Dodge 2011 Challenger SRT, Owner'S Manual

The Dodge 2011 Challenger SRT is a powerful and stylish car that combines classic muscle car design with modern performance. To fully understand and maximize the potential of this exceptional vehicle, it is crucial to have the Owner's Manual. You can conveniently download the manual for free from manualshive.com, ensuring a seamless and enjoyable ownership experience.

Share
Download
background image

The engine block heater must be plugged in at least one
hour to have an adequate warming effect on the engine.

WARNING!

Remember to disconnect the engine block heater
cord before driving. Damage to the 110-115 Volt
electrical cord could cause electrocution.

MANUAL TRANSMISSION — IF EQUIPPED

Six-Speed Manual Transmission

WARNING!

You or others could be injured if you leave the
vehicle unattended without having the parking
brake fully applied. The parking brake should al-
ways be applied when the driver is not in the vehicle,
especially on an incline.

CAUTION!

•

Never drive with your foot resting on the clutch
pedal, or try to hold the vehicle on a hill with the
clutch pedal partially engaged, as this will cause
abnormal wear on the clutch. Refer to “Electronic
Brake Control System/Hill Start Assist

ⴖ

in “Start-

ing and Operating” for further information.

•

Failure to press the clutch pedal fully to the floor
may cause increased shift efforts, and may result
in damage to the clutch and transmission.

•

Do not rest your hand on the shift lever while
driving, as this may result in transmission syn-
chronizer damage.

•

Do not attempt to shift the transmission if the rear
wheels are spinning due to loss of traction. Dam-
age to the transmission may occur.

5

STARTING AND OPERATING

257

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger SRT

Yakima Q46 Installation Instructions preview
Q46
Brand: Yakima Pages: 4
Mazdaspeed QSEA 51 96Z Installation And User Instructions Manual preview
QSEA 51 96Z
Brand: Mazdaspeed Pages: 8
Victory 4x4 5TH GEN 4RUNNER Install Instructions preview
5TH GEN 4RUNNER
Brand: Victory 4x4 Pages: 5
Keith WALKING FLOOR Helpful Hints preview
WALKING FLOOR
Brand: Keith Pages: 2
Toyota 1973 Crown Hardtop Owner'S Manual preview
1973 Crown Hardtop
Brand: Toyota Pages: 50
DAF PACCAR PACMOBILE 20 User Manual preview
PACCAR PACMOBILE 20
Brand: DAF Pages: 18
Parkeon StradaPAL Installation Manual preview
StradaPAL
Brand: Parkeon Pages: 43
Calitop Calispace Ocean 80 Assembly Instructions preview
Calispace Ocean 80
Brand: Calitop Pages: 5
travall TDG-1301 Fitting Instruction preview
TDG-1301
Brand: travall Pages: 2
Gacell 13553 User Manual preview
13553
Brand: Gacell Pages: 12
EUFAB 16458 Operating Instructions Manual preview
16458
Brand: EUFAB Pages: 16
Mercedes-Benz Sprinter 2003 Manual preview
Sprinter 2003
Brand: Mercedes-Benz Pages: 296
Gator GT700SD User Manual preview
GT700SD
Brand: Gator Pages: 6
F.lli Menabo CROSS 2 Assembly Instructions Manual preview
CROSS 2
Brand: F.lli Menabo Pages: 16
true-i HMBS-200 User Manual preview
HMBS-200
Brand: true-i Pages: 11
Classic AutoAir Mustang 1969 Installation Manual preview
Mustang 1969
Brand: Classic AutoAir Pages: 44
Mitsubishi Montero 1988 Manual preview
Montero 1988
Brand: Mitsubishi Pages: 367
CITROEN 1953 Traction Avant User Manual preview
1953 Traction Avant
Brand: CITROEN Pages: 26

Brands by name

Popular brands

Load more brands