Dodge 2011 Challenger SRT Owner'S Manual Download Page 52 | Manualshive

Page: 52 / 459

background image

5. Position the shoulder belt on your chest so that it is
comfortable and not resting on your neck. The retractor
will withdraw any slack in the belt.

6. To release the belt, push the red button on the buckle.
The belt will automatically retract to its stowed position.
If necessary, slide the latch plate down the webbing to
allow the belt to retract fully.

WARNING!

A frayed or torn belt could rip apart in an accident
and leave you with no protection. Inspect the belt
system periodically, checking for cuts, frays, or loose
parts. Damaged parts must be replaced immediately.
Do not disassemble or modify the system. Seat belt
assemblies must be replaced after an accident if they
have been damaged (bent retractor, torn webbing,
etc.).

Removing Slack From Belt

50

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
50
51
52
53
54
...
»

Summary of Contents for 2011 Challenger SRT












































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger SRT

Brand: A-Tach Mounts Pages: 2

Brand: Fabbri Pages: 4

Brand: Velleman Pages: 6

Brand: PullRite Pages: 10

Brand: STC Pages: 6

2012 Truck Chassis cab

Brand: RAM Pages: 506

Brand: TAUBENREUTHER Pages: 8

Brand: Jeep Pages: 136

Brand: Sanitas Pages: 36

Brand: Huf Pages: 6

Brand: Kuda Pages: 3

Even Brake 9400

Brand: Roadmaster Pages: 20

Brand: Lexus Pages: 6

Brand: Rugged Ridge Pages: 3

Brand: TATA Motors Pages: 146

Pro Competition

Brand: G-Tech Pages: 180

10-8002-C12167A

Brand: Saleen Pages: 6

Brand: Hellwig Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands