Digital Projection E-Vision Laser 15000 Series Installation & Quick Start Manual Download Page 63

Page: 63 / 145

Using the projector

Digital Projection E-Vision Laser 15000 Series

Geometry

Aspect Ratio

Source

Digital Zoom

►

Overscan

Off

Blanking

►

Warping Mode

Keystone

►

4 Corners

►

Rotation

►

Pincushion / Barrel

►

Arc

►

Custom Warp

►

Warp Filter

►

Select a

Warping Mode

activate it. Access its submenu to
adjust the warping mode settings.

This menu allows you to compensate for image distortions caused by an unusual projection angle or irregular
screen surface.

Aspect Ratio

Image scaling and aspect ratio are
also influenced by

Setup > Screen

Setting

See Theaterscope setting on the
next page for further information
about the

TheaterScope

aspect

ratio.

This feature defines the aspect ratio of the source. Use the

Setup > Screen Setting

to define the screen aspect ratio.

If you choose a preset aspect ratio from here, it will give you the best fit for your selection.

Choose from:

5:4

4:3

16:10

16:9

1.88

2.35

TheaterScope

Source

Unscaled

Operating Guide

Rev B April 2021

page 63

Notes

Summary of Contents for E-Vision Laser 15000 Series


















































































































































Search results

Summary of Contents for E-Vision Laser 15000 Series

Reviews:

Related manuals for E-Vision Laser 15000 Series

Brands by name

Popular brands

Digital Projection E-Vision Laser 15000 Series, Installation & Quick Start Manual

Search results

Summary of Contents for E-Vision Laser 15000 Series

Reviews:

Related manuals for E-Vision Laser 15000 Series

Brands by name

Popular brands