Digital Projection E-Vision Laser 15000 Series Installation & Quick Start Manual Download Page 11

Page: 11 / 145

General Precautions

Digital Projection E-Vision Laser 15000 Series

Do not touch the ventilation outlets, as they will become hot in use.

Do not cover or obstruct the ventilation outlets or inlets.

Do not cover the lens whilst the projector is switched on. This could cause a fire.

Always allow the projector to cool for 5 minutes before disconnecting the power or moving the projector.

Never use strong detergents or solvents such as alcohol or thinners to clean the projector and lens.

Introduction

Rev B April 2021

page 11

Notes

Summary of Contents for E-Vision Laser 15000 Series


















































































































































Search results

Summary of Contents for E-Vision Laser 15000 Series

Reviews:

Related manuals for E-Vision Laser 15000 Series

Brands by name

Popular brands

Digital Projection E-Vision Laser 15000 Series, Installation & Quick Start Manual

Search results

Summary of Contents for E-Vision Laser 15000 Series

Reviews:

Related manuals for E-Vision Laser 15000 Series

Brands by name

Popular brands