background image

12

EN

16652807_en 05 /2006

1.7

Authorised users

Youths under 16 years of age may not operate the round baler.
The owner of the machine must make the operating instructions available to the user and ensure that the
latter has read and understood same. Only then may the user operate the machine.
The delegation of responsibility for various machine duties must be clearly established and adhered to.
There must be no doubt regarding the user´s competence as this could put the user at risk.
The owner must ensure that only authorised persons work on the machine. He is responsible for third
parties for the area in which the round baler is being used.

1.8

General safety and accident prevention regulations

Basic rule:

Basic rule:

Basic rule:

Basic rule:

Basic rule:

Check that the device and tractor are road worthy and operationally safe before each start-up. Note
the generally applicable safety and accident prevention regulations as well as the instructions in these
operating instructions.

1.8.1 General

1. The warning and notice signs posted provide important information for risk-free operation.

Please note these instructions for your own safety.

2. Make yourself familiar with all equipment, operating elements and their functions prior to commencing

work. Ensure that all protective devices are properly attached.

3. The user´s clothing must fit closely. Do not wear baggy clothes. Wear sturdy shoes.
4. Keep the machine clean. Be aware of the risk of fire.
5. When using public thoroughfares, please observe the following:

z

the statutory road traffic regulations,

z

the permissible axle loads and total weights,

z

the permissible transport dimensions.

z

Never leave the operator´s platform while travelling.

6. The equipment must be in the condition prescribed for road transport and be locked according to

the manufacturer´s instructions.

7. Check and secure transport equipment and the lighting, warning and protective equipment.

Summary of Contents for MP135 R































































Reviews: