Dell Vostro 220 - Vostro 220 Slim Desktop Computer Service Manual Download Page 76

Page: 76 / 138

Drives

Holding the front-panel insert at an angle, insert one end into the
drive bay opening.

Push the other end of the insert into the opening until it fits into
place.

NOTE:

To comply with FCC regulations, install the 3.5-inch front-panel insert

whenever the device is permanently removed from the computer.

For the Vostro 220s, push the release latch down to resecure the optical
drive.

Install the cover for the empty bay onto the bezel:

From the inside of the bezel, while holding the cover at an angle,
insert the tab on one end of the cover into the slot on the
corresponding end of the bezel opening.

Lower the cover until it fits securely in the bezel opening.

3.5-inch front-panel insert

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer











































































































































Search results

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer

Reviews:

Related manuals for Vostro 220 - Vostro 220 Slim Desktop Computer

Brands by name

Popular brands

Dell Vostro 220 - Vostro 220 Slim Desktop Computer, Service Manual

Search results

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer

Reviews:

Related manuals for Vostro 220 - Vostro 220 Slim Desktop Computer

Brands by name

Popular brands