Dell Vostro 220 - Vostro 220 Slim Desktop Computer Service Manual Download Page 28

Page: 28 / 138

Troubleshooting

• Remove and then reinstall all memory modules (see "Replacing or Adding a Memory

Module" on page 104).

• Remove and then reinstall any expansion cards, including graphics cards (see "PCI and

PCI Express Cards" on page 59).

LIMINATE

INTERFERENCE

—

Some possible causes of interference are:

• Power, keyboard, and mouse extension cables

• Too many devices connected to the same power strip

• Multiple power strips connected to the same electrical outlet

Printer Problems

CAUTION:

Before you begin any of the procedures in this section, follow the

safety instructions that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at
www.dell.com/regulatory_compliance.

NOTE:

If you need technical assistance for your printer, contact the printer’s

manufacturer.

HECK

THE

PRINTER

DOCUMENTATION

—

See the printer documentation for setup

and troubleshooting information.

NSURE

THAT

THE

PRINTER

TURNED

HECK

THE

PRINTER

CABLE

CONNECTIONS

—

• See the printer documentation for cable connection information.

• Ensure that the printer cables are securely connected to the printer and the computer.

EST

THE

ELECTRICAL

OUTLET

—

Ensure that the electrical outlet is working by

testing it with another device, such as a lamp.

ERIFY

THAT

THE

PRINTER

RECOGNIZED

INDOWS

—

Windows XP:

Click

Start

→

Control Panel

→

Printers and Other Hardware

→

View installed

printers or fax printers

If the printer is listed, right-click the printer icon.

Click

Properties

→

Ports

. For a parallel printer, ensure that the

Print to the following

port(s):

setting is

LPT1 (Printer Port)

. For a USB printer, ensure that the

Print to the

following port(s):

setting is

USB

Windows Vista

Click

Start

→

Control Panel

→

Hardware and Sound

→

Printer

If the printer is listed, right-click the printer icon.

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer











































































































































Search results

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer

Reviews:

Related manuals for Vostro 220 - Vostro 220 Slim Desktop Computer

Brands by name

Popular brands

Dell Vostro 220 - Vostro 220 Slim Desktop Computer, Service Manual

Search results

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer

Reviews:

Related manuals for Vostro 220 - Vostro 220 Slim Desktop Computer

Brands by name

Popular brands