Dell Vostro 220 - Vostro 220 Slim Desktop Computer Service Manual Download Page 120

Page: 120 / 138

120

System Board

Remove the memory modules from the system board (see "Replacing
or Adding a Memory Module" on page 104) and place them
individually into antistatic packaging.

Remove the processor from the system board (see "Removing the
Processor" on page 125) and place it into antistatic packaging.

Disconnect the chassis fan cable from the system board.

Disconnect any additional cables from the system board.

Remove the screws that secure the system board to the computer chassis.

CAUTION:

The system board is extremely fragile. Exercise great care when

handling the system board.

Carefully lift the system board out of the computer chassis and place it
into antistatic packaging.

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer











































































































































Search results

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer

Reviews:

Related manuals for Vostro 220 - Vostro 220 Slim Desktop Computer

Brands by name

Popular brands

Dell Vostro 220 - Vostro 220 Slim Desktop Computer, Service Manual

Search results

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer

Reviews:

Related manuals for Vostro 220 - Vostro 220 Slim Desktop Computer

Brands by name

Popular brands