Dell Vostro 220 - Vostro 220 Slim Desktop Computer Service Manual Download Page 67

Page: 67 / 138

Drives

Vostro 220

For the Vostro 220s:

Raise and hold the hard-drive release latch.

Slide the drive partway out of the bay, rotate the back of the drive
upward until the drive is perpendicular to the drive cage, and guide
the screws through the cutaway channels in the drive cage until you
can lift the drive away from the computer.

Repeat step a and step b for the second hard drive, if installed.

screws (4)

hard drive

power cable

data cable

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer











































































































































Search results

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer

Reviews:

Related manuals for Vostro 220 - Vostro 220 Slim Desktop Computer

Brands by name

Popular brands

Dell Vostro 220 - Vostro 220 Slim Desktop Computer, Service Manual

Search results

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer

Reviews:

Related manuals for Vostro 220 - Vostro 220 Slim Desktop Computer

Brands by name

Popular brands