Dell Vostro 220 - Vostro 220 Slim Desktop Computer Service Manual Download Page 136

Page: 136 / 138

136

Safety Instructions

BIOS

The system setup program resides within the BIOS on the system board. If
you install a new system board, you may need to update (or

flash

) the BIOS.

Flashing the BIOS From the Hard Drive

Turn on the computer.

Locate the latest BIOS update file for your computer at

support.dell.com

Click

Download Now

to download the file.

If the

Export Compliance Disclaimer

window appears, click

Yes, I Accept

this Agreement

The

File Download

window appears.

Click

Save this program to disk

, and then click

The

Save In

window appears.

Click the down arrow to view the

Save In

menu, select

Desktop

, and then

click

Save

The file downloads to your desktop.

Click

if the

Download Complete

window appears.

The file icon appears on your desktop and is titled the same as the
downloaded BIOS update file.

Double-click the file icon on the desktop and follow the instructions on
the screen.

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer











































































































































Search results

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer

Reviews:

Related manuals for Vostro 220 - Vostro 220 Slim Desktop Computer

Brands by name

Popular brands

Dell Vostro 220 - Vostro 220 Slim Desktop Computer, Service Manual

Search results

Summary of Contents for Vostro 220 - Vostro 220 Slim Desktop Computer

Reviews:

Related manuals for Vostro 220 - Vostro 220 Slim Desktop Computer

Brands by name

Popular brands