Dell D28M Service Manual Download Page 66 | Manualshive

Page: 66 / 94

Dell D28M Service Manual Download Page 66

Steps

1. Slide the front I/O-ports on the system board into the front I/O-slots on the chassis and align the screw holes on the system board

with the screw holes on the chassis.

2. Replace the screw (M2x4) that secures the system board to the chassis.
3. Replace the eight screws (#6-32) that secure the system board to the chassis.
4. Route and connect all the cables that you disconnected from the system board .
5. Align the front I/O-bracket with the slots on the chassis.
6. Replace the screw (#6-32) that secures the front I/O-bracket to the chassis.

Next steps

.

processor fan and heat-sink assembly

.

coin-cell battery

solid-state drive/Intel Optane memory module

.

.

10. Install the

left-side cover

.

11. Follow the procedure in

After working inside your computer

.

NOTE:

Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup

program after you replace the system board.

NOTE:

Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup

program. You must make the appropriate changes again after you replace the system board.

66

Disassembly and reassembly

«
...
64
65
66
67
68
...
»

Summary of Contents for D28M































































































Reviews:

No comments